DIY bench made from old chairs. A bench made from two old chairs. DIY pallet bench

To garden plot was quite comfortable, it should be properly equipped. An important component are garden benches. You can make them yourself different ways and from various materials.

Bench made of concrete slabs and boards with backrest

By looking at the drawings of the bench, you can find out the features of its structure. You can make such a design with your own hands relatively easily, quickly and without high financial costs.

Making a bench with a backrest with your own hands in step by step instructions described in great detail.

Assembly: initial stage

After preparatory work The time for wood processing is approaching. In order for a hand-made bench with a back to serve for a long time and decorate the area, the materials must be pre-treated.

The tree is covered antiseptic compounds and let it dry. After this you can start collecting backrests

On one of the two-meter boards, fifty centimeters are measured from the edges. At this level the edges of the beton slabs. From this mark another fifteen centimeters are measured towards the center of the board. This is where the first boards will be attached. From the resulting marks we measure seventeen and a half centimeters - the gap between the back boards. Next, we measure fifteen centimeters for two more boards. There should be a gap of five centimeters between them. All this can be seen in the drawing.

Wood glue is applied to fifteen centimeter sections. They are attached to boards, the length of which is sixty-five centimeters. Additionally, they are secured with self-tapping screws.

On top, between the boards of the back, pieces of seventeen and a half centimeters are glued. To ensure that the parts stick together well, they are clamped and held until the glue sets. After gluing is completed, the back is covered with an antiseptic.

All wooden parts can be covered varnish. This will give them additional stability and attractiveness.

Assembly of the main part

It is better to assemble the main part of the bench from both sides. Placed between the boards concrete plates, and in drilled holes insert M16 threaded rods fifty-five centimeters long. You will need four of them.

The rods are fastened with M16 nuts and washers. They are twisted simultaneously from different sides to make the bench level.

Simple DIY bench

You can make benches for your garden with your own hands quite quickly if you follow the instructions. Let's consider four options for such garden structures.

On drawings benches, all its features are indicated in detail. Making such a bench with your own hands is quite simple. The only difficult element is the concave seat.

The number of parts and their dimensions are indicated in the table.

We begin making a bench with our own hands from wood with blanks necessary details. Boards and beams are cut into pieces required length.

Making seat supports will be somewhat more difficult. You will need to mark the blanks. Two points are marked along the edges at a distance of seven and a half centimeters from the bottom side, and in the center a point at a distance of four and a half centimeters. They are connected using a flexible plastic ruler and cut out jigsaw. The sections are processed with sandpaper.

The seat supports are attached to the two upper drawers. One on each edge and one in the middle. Next, screw in the supports, spaced from the outer ones by the width of the leg. All connections are made with self-tapping screws.

Boards are attached to the resulting base seats. It is advisable to deepen the screw caps.

Then attach legs. They are attached to the seat supports. The lower drawers help secure the legs.

The finished product is coated antiseptic and varnish.

Simple bench No. 2

To make such a garden bench with your own hands, you will need concrete flower girls and boards. Flower girls are required to create the base of the bench. Use two with a rectangular base and two cubic ones.

To make the base stable, the flower boxes must be glued or connected from the inside with staples secured with self-tapping screws. The container is filled with a layer of drainage and soil. This increases their stability.

The seat for the bench is made of boards. To do this, they are cut into pieces of the required length. These blanks are laid so that there is a distance of half a centimeter between them. Then they are connected using transverse strips. The planks are placed in three places: at the edges and in the middle. Corners are attached to the slats. With their help, the seat will be secured to the flower girls.

DIY bench with backrest

Prepare the bench parts shown in the figure. They are being processed antiseptics before connecting.

Then the parts are assembled into supports. The corners are first rounded and chamfered. First, parts A and B are connected with a bolt, and then B, C and D are also connected using a bolt.

The inclination of the backrest is determined by part D, after which it is connected to part A. Similarly, but in a mirror image, another support is made.

After this, the back and seat are assembled. To do this, the supports are placed so that there is a distance of one meter and twenty centimeters between them. First, the front and rear strips are screwed to the supports, then all the rest, and finally the stops are screwed in.

At the last stage, the back of this bench is screwed on.

Bench No. 4Another option for a simple DIY bench. Its length is one hundred twenty centimeters. The height from the ground to the seat is fifty centimeters, the height of the backrest is also fifty centimeters.

The base is made from boards, the thickness of which is five centimeters and the width from ten to twelve. One of the legs continues and serves as a support for the back. The supports are connected using the “half-tree” method and secured with bolts.

The basis for the seat is a block secured with self-tapping screws. The short supports on the back of the bench are connected with a collet to increase stability. The seat and back are covered with boards of less thickness. The surface is painted or varnished.

A simple bench with a back for a summer cottage

The dimensions of the structure and wooden parts can be seen on drawings benches. If we consider how to make a bench with our own hands, then this option will be the most optimal in terms of the simplicity of the process and the result obtained.

It is better to purchase materials already cut to size. If this is not an option, then you need to cut them yourself.

The resulting blanks polished. The ends of the boards are processed with an electric planer.

The back legs of this simple DIY bench also support the backrest. To create the desired level of inclination, the workpieces are marked.

At a height of forty centimeters, mark the attachment point seats. Above, the board is cut at an angle of twenty degrees. The cuts on the two workpieces must be identical.

First they collect legs benches: the front ones are connected to the back ones using a beam. It is better to do this from above and below.

When the side parts are assembled, they can be connected to each other with seat boards. Screw the boards with self-tapping screws, leaving a distance of one or two centimeters.

To strengthen the structure and increase its stability, make the lower harness timber along the legs. Two boards are attached for the back.

Finish the work with finishing coated, which will protect the product from moisture and adverse conditions.

DIY pallet bench

Make a bench with your own hands from pallets It’s not difficult if you use your imagination. To do this you will need three or four of these wooden structures. Some will need to be sawed to obtain additional parts. The most simple design DIY benches made from pallets, when two pallets are attached perpendicular to each other, creating a back and seat.

To prevent the design from becoming too bulky, it is better to cut the pallets according the right sizes. The elements are fastened with self-tapping screws. Add side parts to enhance strength and make legs. All this can be seen in the photo.

Since the material of the pallets is untreated and rough, it will be required first polish. This will allow you to avoid splinters.

The manufacture of a bench with your own hands from pallets is completed by coating it with varnish or paint.

Bench puzzle

You can make such a bench with your own hands if you have a wide board and cuttings for shovels. Curly seats are cut out of the board in the form of puzzle pieces. Legs made from cuttings for shovels are attached to them. The result is separate stools that quickly assemble into one long bench. All manufacturing stages are discussed in detail in step-by-step photos.

Benches from unnecessary chairs: two DIY options

First option

To create such a bench for your dacha with your own hands, you will need four old chair.

From the first two chairs remove parts from the front of the seat.

The remaining sawed off the front legs are slightly lower than the seat structure.

From the resulting parts you need take off old varnish or paint. To do this, apply to the parts special remedy, dissolving paint coatings. Then the softened layer can be removed with a spatula.

The racks should drill holes for dowels. Holes are required on the front and end sides.

The dowels are lubricated with glue and inserted into the drilled holes.

When the dowels are glued, you can assemble base benches. To make the structure durable, the parts are fastened with self-tapping screws. Surface of the structure sanded.

For seats benches choose a board that is suitable in size, saw off the excess.

If several narrower boards are used, they are glued together with wood glue. For a tight connection, they are clamped with clamps and wait for the glue to dry.

The finished seat is also glued to the base with wood glue. Heavy objects are placed on the board and clamped together with the base with clamps.

When the glue has dried, cover the seat with masking tape and paint paint the remaining structural elements for wood.

The tape is removed and the seat is treated stain. Finally, the entire bench is varnished.

Second option

To make a second garden bench with your own hands from old furniture you will need two chairs. It is better if the back and hind legs are not separated.

Two identical chairs clean up all parts of the structure except the rear legs with the back.

They take bars five centimeters wide and three centimeters thick. Cut two parts equal in length to the width of the chairs, and two pieces of the same length as the finished bench. A rectangle is assembled from these four parts. It is secured to the backs of chairs with self-tapping screws.

Another frame is assembled in the same way. Several transverse strips are attached to it. This design is attached under the seat, makes the bench more reliable and acts as a shelf.

If the chairs have old covering, then it is removed sandpaper. After this, the surface is puttied special composition or coated with a primer. When the layer has dried, it must be sanded with fine-grained sandpaper. Finally, the structure is coated with paint.

The seat for the garden bench is made by hand from Chipboard or plywood. A rectangle is cut out of the selected material, which is half a centimeter larger than the base on each side. Then cut out a piece foam rubber with the same dimensions. A rectangle is cut out from upholstery fabric. It should be five centimeters larger than the seat on each side.

Foam rubber is placed on a sheet of plywood and covered with fabric on top. The fabric is attached from the inside out to the furniture stapler.

The seat is attached to the base with a piano hinge.

Bench-swing

To make such a bench for your dacha with your own hands, you should prepare necessary materials. Manufacturing begins with creation basics designs. The seat bars are attached to the back bars at the selected angle.

Additional ones are installed along the seat ribs, providing rigidity.

Attached to the seat planks, drilling holes for fastening in the base bars. The same goes for the back.

Armrests are installed on both sides of the seat. They can be secured with bolts.

The resulting bench cover wood protection products and varnish. It is very important to paint everything as carefully as possible.

The bottom of the bench is reinforced with metal profile. Chains are attached to the profile on which the swing bench will be suspended. It is imperative to check the reliability of the beams on which the bench will be suspended.

Log bench

To make such a bench with your own hands from wood you will need chainsaw. The main material is a thick log one meter long.

Log mark, so that you get two slightly unequal parts. The smaller one will be used to make the backrest, and the larger one will be used to make the seat.

Chainsaw log sawed along the mark. The resulting irregularities are immediately cut off with the same saw.

The cut triangular piece is cut into pieces and inserted into the holes in the seat. The back is secured on top. The bench is almost ready. All that remains is to give it a more decorative look.

Can the seat be placed on legs. To do this, recesses are made in the lower part to install a pair of logs as legs.

Transformable bench

The design features of the transformer can be seen in the drawings of the bench. A transformer bench is made with your own hands from planed boards, which is sawn to the specified dimensions.

Sliced timber parts holes for fasteners are drilled.

At the table top, the boards located on the edge can be made wavy.

In material intended for countertops, drill holes with a diameter of twenty-two millimeters and a depth of three centimeters. Cuttings of the same diameter will be inserted into them.

The edges of parts and edges are processed and rounded.

All elements are assembled using screws and screws. Screws are needed with dimensions 6x70 and 6x90, screws - 8x80.

Wooden parts are painted stain.

The structural parts that will move are connected by hinges.

Parts of a round shape are placed between the boards of the tabletop. cuttings

Install a stop for backrests

A hand-made transformer bench is covered varnish.

Rocking bench

Making an original bench with a backrest with your own hands is not difficult if you have the tools and materials. First you need to consider the drawings of the bench, which contain a small number of parts.

The side parts according to the pattern are transferred to Europlywood three centimeters thick. They are cut out using a jigsaw and the ends are processed with a grinder.

To attach the connecting strips, markings are made. Then the holes are drilled. After assembling the frame, the slats are attached using self-tapping screws. The fastening points are sprayed, and the entire product is varnished.

Bench around a tree

The simplest version of such a bench is hexagonal The size depends on the size of the tree. Measurements are taken at the height of the seat. A margin of fifteen to twenty centimeters is added to the result obtained. If you divide the result by 1.75, you will get the length of the inner side.

To cut boards ten centimeters wide, they are laid in four rows with intervals of one centimeter.

The cutting location is marked immediately for all rows with an angle of thirty degrees. So cut out six sets of blanks.

Legs are used with a height of sixty to seventy centimeters. They are connected by cross members by drilling holes and using bolts and nuts.

The seat is installed so that the joints are located in the center of the ribs of the legs. The outer parts are screwed on first, and then the inner ones. In this way, the entire hexagonal structure around the tree is assembled.

Finally, the back is made and the apron is installed. The result is a DIY circular bench with a backrest.

The finished product is processed oil impregnation.

Bench made of curved branches

A bench made of curved branches will look original. It will require branches for the front part, two legs, a horizontal top and a pair of transverse branches.

Sawing branches so that they fit each other as accurately as possible. Next they are connected by metal corners.

The back part is made in the same way and connected to the front.

The finished product is placed on a flat surface and the seat is assembled.

Bench options

Log bench, which blends well with the surrounding nature. It consists of half a log, used for a seat, and two short round logs, which are legs.
Beautiful wooden bench with a back and armrests, reminiscent of a sofa. Curved and cut elements make it more attractive, while leaving knots and irregularities gives the structure a natural look.
Bench made of wood and metal. The base of the structure is metal. The wooden parts of the seat and back are attached to it. Thanks to the small thickness metal parts she looks light.
The bench has a simple, classic shape. It is made of wooden, rather wide boards. This width allows you to sit comfortably on the bench. Armrests make the design more complete.
Original bench made of wood with figured details. This option is well suited for a site with a natural, rural design. Carved legs and armrests, a figured back - all this gives the product originality.
Bench with an interestingly shaped back. The curved parts gradually bend back, creating a unique design. The seat is slightly curved but has a more traditional appearance.
Wooden complex- a table with two benches. The design looks traditional due to the material used. An original solution is the fastening of all components into a single structure.
The bench is made of solid logs. A single piece is cut out of it, combining the back and seat. The legs are attached to the bottom. The log required is quite large.
Bench with storage box for toys. Outwardly it looks like an ordinary wooden bench-sofa, but under the seat there is a drawer in which you can put various things.
A comfortable bench made of wood with a simple shape. The base is made in the form of a rectangular box. The back is also simple with a straight shape. Placed on the seat soft pillows, providing additional comfort.
Wooden bench located around a tree. It is made as if it consists of four benches, each of which has one armrest. The composition looks attractive and comfortable.
A simple bench made of wide boards. It looks solid, but its dimensions are somewhat concealed due to the gaps between the boards and the light blue, in which it is painted.

How to make a bench from old chairs? Let's talk.

In this tutorial we are using four old chairs. We need two of them almost completely; from the remaining two it is convenient to saw off the missing parts to obtain a bench. In general, two chairs are enough, but then you will need additional boards.

If the chairs are very old and have already begun to fall apart a little, then choose the two strongest from the four. From the other two we will need front crossbars. The photo shows which ones exactly. They can either be sawed off or untwisted if the structure is prefabricated.

The front legs need to be sawed off from the two main chairs. For convenience, you can mark a line along which you will cut.

Before we start assembling, we need to get rid of old paint. To do this you will need paint thinner. Buy any from a hardware store and follow the instructions on the package. For convenience, lay a piece of unnecessary tarpaulin, old newspapers or film as a working surface. Be sure to wear rubber gloves before applying solvent. Don't forget to apply solvent to the boards we prepared to join the chairs into the bench.

Let the solvent sit for the time required according to the instructions. To remove old paint, use a spatula, preferably a metal one.

Let's start assembling. Use to attach boards to chairs furniture dowels. Carefully mark the location of the dowels using a marker and ruler so that all holes are at the same level. Wrap the drill bit with masking tape to mark the desired depth of the hole.

For more secure fastening of dowels in the holes, use wood glue.

To make the structure more durable, add a bench in the middle wooden beam. Measure the distance between the chairs, cut the timber to the required length and secure it with screws. After assembly, you need to start sanding the surfaces. Use sandpaper or a sander.

Now you need to make a seat for the bench. You can either purchase timber in the store or use the remnants of old ones left in the garage from previous work. Lay the timber on edge on the bench to get an idea of how much you need.

We glue the beams together using wood glue. Clamp with clamps and leave for a day.

Now we need to trim the edges of the seat surface to the shape of the chairs. In our case they are rounded. We mark a pencil line and use a jigsaw to saw off the unnecessary part.

Place the seat on the chairs and secure them with screws. You can only use wood glue, then after gluing, place some weight on the seat. But it will be more reliable with screws.

Sand the surface of the seat after finishing the job. Now all that's left to do is paint the bench. For a chair structure, use paint, first covering the seat with film and sealing the sides with masking tape. Paint the seat itself with varnish. If you have different beams, as in our instructions and it looks aesthetically pleasing, you can use transparent varnish. Leave the bench for several days until completely dry.

1. Materials:
- two old wooden chairs;
- dye;
- water-based varnish;
- solvent for degreasing the surface;
- putty;
- coarse and fine grain sandpaper;
- screws and nails;
- strong threads for the cover;
- furniture foam rubber 40 - 50 mm;
- furniture or any other fabric (can be used).

2. Tools:
- rubber spatula for putty;
- brushes for applying varnish and paint;
- hammer;
- clamps;
- screwdriver;
- a sharp knife for cutting foam rubber, scissors;
- Sander(you can do without it);
- sewing machine.

Step 1: searching for material

So, we need a couple of unnecessary rickety grandma chairs that are probably languishing in your garage or closet. In any case, at the flea market you can find and buy these for pennies.

In addition to the chairs, prepare boards for the frame of the bench and plywood, from which we will make the base for the seat, as well as the shelf under it. The latter can be quite functional.

Step 2: preparing materials

Start by taking the chairs apart. We need to disconnect the back part of the chair on which the backrest is located. These backrests will serve as the sides of a future garden bench.

Next, from the remnants that remained after disassembling the chairs or suitable bars of the required cross-section, we assemble the frame of the product. We followed the principle and used the remains of old chairs, since in general they seemed to us to be pretty good.
The base will be rectangular, of arbitrary length, but choose the optimal dimensions - such that ready product had the strength necessary for intensive use.

Screw a sheet of plywood to the base.

Step 3: Assembling the Bench

We connect the resulting parts, forming a prototype of the future bench for the dacha. For additional strength, we arrange a strapping of slats along the perimeter below - exactly the one on which the shelf we have planned from the remaining plywood will lie.

Step 4: take care of aesthetics

Now you have the most important work ahead of you, on which the final result of all the work done will depend.

Thoroughly clean the bench from dirt and dust. Sand all surfaces and, if necessary, sharp corners and edges, giving them a slightly rounded appearance - first with coarse sandpaper, then with fine-grit sandpaper.

Fill cracks, joints and uneven areas with putty using a rubber spatula. Sand everything well again. The process takes quite a long time and requires patience, but believe me, the end result is worth it. All elements will acquire complete outlines and an aesthetic appearance.

Treat the surface with solvent and start painting. Apply the first coat, let it dry completely, then sand to allow the next coat of paint to penetrate the previous one. Paint all the parts a second time, wait until dry and apply a coat of varnish.

It is better to do the same with varnish as with paint - lightly sand and re-varnish. Thus, you will receive a coating that is very resistant to external influences. And since the bench will presumably be located outside under a canopy, this will come in handy.

Step 5: finishing touch

Sew a cushion for sitting. To do this, cut sharp knife a piece of furniture foam rubber of the required size. Having attached to it a piece of furniture fabric, which is usually used for upholstering sofas, decide on the size of the cushion cover, not forgetting to add a little for seam allowances.

Actually buy furniture fabric not necessary. You can use any other durable material, and it doesn’t have to be new.

Sew the cover and sew a zipper into it on the side. This will make it easier for you to care for your pillow in the future. Place the foam in the case and place it on the seat. A pair of bright pillows will complement the ensemble.

Do you have a couple unnecessary chairs that stand idle? Today we will tell you how to make a cool bench out of them french style, which is ideal for interior decoration.

On our balcony we found old wooden chairs, about 50 - 60 years old. They had a soft seat and were made of thin wood. At the moment when we took up this matter, they were already falling apart.

We named the bench French because we saw a similar bench from Ballard Designs. We also want to emphasize that this is not one of those benches that are made by lining up chairs in a row, where plywood is later placed on them. After all, it looks a little strange, we will make a bench in a classic style.

If you do make such a bench, you will probably have your own thoughts and ideas on how to make it better. We will be glad to accept your advice and work. Send them to us by email, we will be happy to share them on our website.

After looking at our chairs, we found out that they were fake, although they looked very expensive. After which, they were safely taken to the farthest corner of the workshop to await their fate. At that moment we simply could not get rid of them. One fine May day, one of our craftsmen suddenly began making our bench without us. This is not like him, because usually we have to persuade him for a long time to do anything, of course, except for custom-made furniture, this is his direct responsibility. So, let's begin!

Step one: Find chairs.

— We need to find two chairs that look good from the outside. If your chairs have a slight backrest angle, that will be great. Such a back will create comfort and a not very angular look. It is advisable that the seat of the chair be screwed with nuts and bolts to the main body. This will make it easier for us to attach the base under the bench to our chairs.

— Remove the front legs and seat. On our fake chairs, everything was held together with glue; we easily tore off the two front legs and removed the seat. This leaves us with two chair backs.

If the front legs of your chairs can be unscrewed, it is better to take advantage of this opportunity. If the legs are broken off, there may be pieces of wood left sticking out.

Step two: Making a bench seat.

— Make a rectangular frame. The length of the bench can be made to any length. It depends on how many people you plan to fit on it. We took materials for our frame from old table top from ikea. After the frame is ready, it must be secured with screws, as shown in the figure above. Use strong screws to make the frame immovable.

— We fasten the frame. We drilled holes into which the seats from the chairs would have been attached if they were not fake, and attached our frame. On each side, we made three holes and screwed in three screws to distribute the weight evenly. A little lower, we drilled a couple more holes and screwed in a future shelf for various things. Our goal is to make the bench safe to sit on, so don't skimp on the bolts, we ended up with 7 screws on each side.

Step three. Create the bottom shelf.

“Even after we attached the main frame to our bench, the structure was still quite shaky. To avoid falls and breaking the bench, we decided to fasten the two sides together with another wooden rectangle. We will use it as a shelf. Carefully measure the distance between the legs, and do not forget about main principle“Measure seven times and cut once.” Don't repeat our mistakes, measure correctly.

— We nail the partitions. We didn't want our bench to look angular or bulky. Instead of the sheet of plywood that was originally supposed to be on the bottom frame, we nailed 5 cross slats. For this we used ordinary, small carnations.

Step four. We sand and paint.

— We remove all irregularities with sandpaper. After which, if there are empty spaces between the frames and the frame, we fill them construction foam or plaster. After that, we go over it again with sandpaper. If we leave the gaps unfilled, over time moisture will accumulate there and gradually destroy our bench from the inside. If you don’t have any plaster or foam at hand, just cover all these holes with paint.

— Painting the bench. We used spray paint, a soft cream color. Apply three even layers and let dry.

The cost of a can of spray paint in Tashkent starts from 10 thousand soums. No more costs for a whole bench.

Step five. Let's make a seat.

— To make a seat , we will need a piece of plywood, chipboard, MDF or fiberboard. From this we will build top part benches.

— Upholstering the seat. For soft filling we used padding polyester. If you don't have it on hand, you can pull out the cotton wool from old mattresses. There is plenty of it there, it will be quite suitable. Well, or the fastest and cheapest way is to buy a small piece of foam. It is sold in furniture and household fittings stores. goods. It is necessary to spread the filler on the plywood so that there is about 1 centimeter of void around the perimeter. The material for covering the bench is also of your choice. We used a piece of scrap sheet. Having covered our soft filler with a cloth, we folded the edges under bottom part benches, and attached it there with a stapler.

— We attach the seat to the body. For mounting, we used an L-shaped bracket. Although everything would have held up just fine with regular bolts, we decided to play it safe and use them.

Our bench is ready! All we have left is to decide whether the pillow will be located there or not. In an unusual environment, with needles in our hands, we decided to try it. Taking the remnants of the sheet that we had left from covering the bench and the padding polyester, we began to sew and fill our pillow. It turned out quite well for people who have been making custom furniture for many years. Making such a bench will take you half a day, or maybe all day. If you have a desire to suddenly do something with your own hands, this bench great option to start. In the courtyard own home or in the country, this piece of furniture will not only be useful, but also beautiful. And having decorated it decorative pillows, a bench will be an excellent tool for decorating a room or area.

I hope that your bench turned out to be as strong as ours. It does not wobble or even sway with a load of about 200 kg. And if something goes wrong, or you simply don’t have enough time, patience or energy, but you still want to get such a bench. You can order it in the custom-made furniture section. And we won’t tell anyone that you didn’t do it.

We think this is a great way to save old chairs and give them a second life. Send your work to us by email. We will be happy to show the world what you have created.

, among which are sometimes pieces of furniture that were very useful, but are outdated and are usually replaced.

But even if you bought new item furniture to replace the old one, the latter can be made into something different, but no less useful.

Old chairs can be found in almost every home, and if you really want to replace them, you still shouldn’t throw them away, since old chairs can be used to make other useful things for your home, garden and cottage.

For example, you can use an old chair to make a towel rack, a garden bench, a convenient pet feeder and much more.

Here are the most interesting crafts that can be made using old chairs:

Remaking an old chair with your own hands: a street bench.

For such a bench you will need two or three chairs. These chairs can be spray painted or left with an antique look.

1.1. If the chairs are too high, you can file down their legs a little.

1.2. You can purchase special cushions for chairs. Some are sold separately (in which case they should be joined with a stitch), but you can also find 4 pads joined together and cut off the excess part.

1.3. To make three chairs look more like one bench, you can purchase or find two or three boards that need to be cut to the required length (the length of three chairs) and joined.

*If desired, you can round the ends.

1.4. Prepare a piece of fabric whose length and width exceeds the length and width of the pads. Lay the fabric pattern down on the floor and place pillows on it.

1.5. Place the joined boards on top of the pads.

1.6. Bend the fabric and use a stapler to attach it to the boards.

1.7. All that remains is to place the boards with cushions on the chairs and add a few simple pillows for decoration.

New life for old wooden chairs: feeders for large dogs.

Tall dogs will find it easier if the feeders are a little higher, especially for older dogs who find it difficult to keep their heads down all the time.

You just need a file tool, a bowl and a pencil.

2.1. Before you start cutting a hole in the chair, you need to sand it first.

2.2. Place the bowl upside down on a chair and trace with a pencil. After this, inside the resulting circle, draw a circle of smaller diameter. This can be done with a compass or a plate of smaller diameter than the bowl.

2.3. Make a hole inside the circle with a drill, from which you can then begin to cut the circle. You can first cut a circle of smaller diameter and check the stability of the bowl in the formed circle. Make the circle even larger if necessary.

2.4. Sand the inside of the hole with sandpaper.

*You can paint the chair and then insert the bowl.

Wall organizer from an old chair with a backrest.

By dividing the chair into parts, you can create wall hanger or an organizer, as well as a comfortable stool.

The back and seat will not be easy to separate, but then everything will be easy.

If necessary, sand all parts and paint.

For the manufacture of comfortable stool you will need:

Tools for separating chair parts

Chair seat

Durable fabric and pillow filling or regular small pillow

Stapler

Hot glue (if necessary) to hold the filled fabric in place.

1. Attach the fabric to the seat using a stapler, but leave one side untouched to fill the resulting pocket with pillow filling.

*You can also use a small pillow instead of filling.

2. Attach the seat back to the chair and you have a beautiful stool.

3. For wall organizer you will need hooks. Once you have screwed or glued the (self-adhesive) hooks, the organizer can be hung on a wall in the hallway, room or bathroom (on a door, for example), where you can hang towels on the hooks.

Repurposing an old chair into a menu board

You can make it out of an old folding chair beautiful board menu.

To do this you will need:

MDF sheets

Seat separation tools

Blackboard paint

Sandpaper (if necessary)

Paint or spray paint (if necessary).

1. From MDF, cut out squares of the required size for each chair (if there is only one chair, then accordingly there will be one square from MDF).

2. Color the square MDF paint for the school board.

3. Remove the seat from the chair and bolt on a painted MDF square in its place.

* IN in this example For beauty, 2 old wooden parts were attached to the board, which matched the shape of the board.

4. To ensure that the legs stand properly, you can attach a chain between them.

How to convert a chair into a coat rack

All you need to do is remove the back of the old chair, sand it down and paint it.

After that, attach the hook of the size you need and hang the hanger in any convenient place.

Bathroom hanger made from an old chair

You will need a chair back. It can be carefully cut down, sanded and painted if desired.

The seat can be cut in half and one half can be used as a hanging shelf.

This shelf can be attached with bolts and special glue. You can use corners to secure the shelf in place. This stage is optional, it is suitable for those who like to work with wood.

Such a hanger can be attached to the door in the bathroom, kitchen, cottage or other room where it may be needed.

How to repurpose old chairs into shoe storage

Separate the seat from the chair. If this is not possible, then you will have to cut it out big hole, into which you will then need to insert the basket.

Find any basket (metal or plastic) and use strong thread or wire to attach it to the chair (by tying it to the frame of the chair).

What to make from an old chair: swing

If you cut off the legs of an old chair, sand it with sandpaper and paint it, it can be used as a seat for a swing in the country or in the garden, for example.

You will need:

Strong rope

Metal rings

Eye screws

Additional details if necessary.

Here is another swing option:

Second life of a chair: garden shelf

An old chair can be turned into convenient shelf for flowers or storage different instruments for garden.

You will need a chair back and part (or all) of the seat. Simply separate the desired part of the seat (you may need to saw off the chair legs) and attach the shelf to the wall or door.

Sand the part with sandpaper and paint.

DIY drinks shelf from an old chair

1. Find a bucket to hold ice and drinks. It is desirable that it have handles that rest on the frame of the chair.

2. Separate the seat from the chair, cut it down or make a hole in the seat.

* Using a strong rope, you can tie a bucket or large bowl to a chair if there are no handles. The most convenient way is to make holes in the bucket through which the thread is threaded.

Second life of an old chair: flowerbed

For the garden you can create beautiful flower bed using an old chair.