Moving the toilet from the riser: to a minimum and long distance. Is moving a toilet considered remodeling? Move the toilet away from the riser

Due to the small area of the bathroom, often when carrying out overhaul bathroom, there is a need to move sanitary equipment. With the aim of effective use free space As a rule, many people prefer to remodel the premises.

The result of this work is the transfer of the toilet from the riser. Because the this process is associated with issues of water supply, drainage of the device, its decision must be taken as responsibly as possible.

Reasons for moving the toilet

Before we begin the process of dismantling the old toilet and installing a new one, we will consider the main reasons for its removal.

Changing the layout of the bathroom. In this case, all operations are coordinated, at a minimum, with the Housing Inspectorate, State Sanitary and Epidemiological Supervision, State Fire Inspection, and Architectural and Planning Department. Only after obtaining permission is the restroom remodeled. When moving a wall, the old location of the device may cause discomfort, which is why there is a need to move it.
Replacing an old device with a new one, which has much big sizes. If, due to the dimensions of the updated design, it cannot be installed on previous place, the product must be moved.
Buying new furniture for the restroom.

Remember, regardless of motivation, old toilet it should be removed intact, the sewerage system should be altered, and only after that proceed with installing the device in another point in the restroom. For this purpose, a long flexible liner is often used.

Moving the toilet (easy way)

This method involves moving sanitary equipment over a distance that does not exceed 30cm.

Before proceeding with the installation of the structure in a new location, it is necessary to dismantle the old device.

The sequence of work depends on the method of installing the plumbing.

If the device is fixed using standard fasteners, and its outlet is connected to the sewer rubber cuff necessary:

unscrew the screws that secure the toilet to the floor;
pull the outlet of the device out of the socket of the sewer line

Let's consider the sequence of work if the toilet is placed on an adhesive or cement base.

Before dismantling the device, you should turn off the water supply valve to the tank and also drain the liquid from the container.

Remove the putty between the outlet of the structure and the sewer socket.

Remember, the work must be performed as carefully as possible to eliminate the possibility of the outlet breaking, otherwise the device is not subject to further use.

Loosen the toilet. For this purpose, a wide chisel is driven in from different sides of the base of the structure.
Pull the outlet, strictly along the axis, from the sewer socket.

After successful dismantling of the structure, the installation process of the product begins. Since the distance from the new location of the toilet to the water supply network and sewerage system is small, there is no need to build up pipelines.

Let's take a closer look at the process of installing a toilet in a new location.

Clean the outlet of the device and the sewer pipe.
Mark new holes in the flooring for mounting the toilet and then drill them out.
Place the corrugation on the outlet of the device; it is important to first apply sealant to the surface.
Seal the gaps between the base and floor covering cement mortar, this will create additional support for the structure.
Insert the corrugation into the socket.

After performing the above operations, you should check the functionality of the device.

Moving the toilet (the difficult way)

If you need to move the device to a distance that exceeds the length of the corrugation, it is necessary to alter the sewer system.

Installation and dismantling of the device will be similar simple way. At the same time, in order to expand the drainage pipeline, a plastic pipe with a diameter of 110 mm is used.

Remember, the length of the structure and the choice of corners depend on the location of the toilet.

Nuances to consider when assembling plastic sewers

Ensure there is a slope towards the riser: 2 cm per linear meter.
When removing the cast iron bend from the tee onto the device, you should first heat the socket using a blowtorch. The result of this procedure is burnout of the bonded seal and cracking of the cement putty. After this, you need to remove the pipe from the socket.

The sewerage system should be installed directly from the riser.

To insert a plastic pipe into a cast iron socket, use a sealing collar.
Cast iron pipe connections filled with sulfur are annealed using a blowtorch.

Remember, in order to minimize labor costs, instead of precisely fitting plastic pipes of the drainage system, you can use corrugation to the toilet outlet.

For efficient functioning sewer system It is important to consider the following rules when connecting plumbing equipment.

The greater the distance from the toilet to sewer riser, the higher it should be placed. This will create required slope pipes for unhindered drainage waste water.

If the structure is very far from the riser, it is necessary to provide for the construction of a podium.

It is prohibited to attach toilets or pipelines to inter-apartment walls, or to move sewer risers.
Plumbing fixtures should be connected to the main line at an angle of 45 or 135 degrees.

Remember, you cannot connect the toilet to the sewer system at a right angle, as this will inevitably lead to the formation of a pipe blockage.

To be able to conduct preventative work, in places where the pipeline turns, it is important to provide special hatches.

Thus, if it is necessary to move the toilet from the riser to a new location, it is important to initially consult with an architect, familiarize yourself with the rules for installing the structure, measure the distance from the sewer system to the device and only then choose necessary method and begin the work process.

Creating a comfortable environment is impossible without remodeling the premises, which also affects the toilet in the apartment.

Possible problems when moving the toilet

Increasing free space toilet room pushes me to think about and reinstall the bathroom. Is it possible to move the toilet to the side?

Yes, but in order for plumbing to function properly, you need to know some subtleties.

Experts voice the following nuances of such a transfer:

The likelihood of a blockage increases with distance from the riser, because sewage travels a long way.
Flushing water is accompanied by an unpleasant odor (sewage stench) and gurgling sounds. A high vacuum is formed in a long pipeline, which leads to water being sucked out of appliances (plumbing fixtures located nearby) and their hydraulic valves breaking.

At the right approach to resolve the issue, such problems can be avoided. Moving the toilet from the riser - a process that is regulated current standards(SNiP).

Requirements for the sewer pipeline:

The use of pipes whose diameter is in the range of 50...100 mm. The optimal cross-section is 100 mm, supplied to the toilet ( minimal risk the appearance of a vacuum or a “plug” of sewage).
The maximum distance from the toilet to the riser is 1.5 m. If the pipe is longer, the power cistern not enough to push through fecal matter. They settle on the walls of the pipeline, and a blockage forms.
Maintaining the correct slope. For each meter of pipeline it is 2 cm (for a cross-section of 100 mm) or 3 cm (for a cross-section of 50 mm).

With a low angle of inclination of the drain, 100% clogging of the sewer is guaranteed, since the fluid flow rate decreases. If the slope is too high, the flow develops excessive speed, which causes solid particles to accumulate in the pipe. As a result, the movement of water is blocked.

The easiest way to obtain the required slope is to provide a podium for installing the toilet, raising it above the surface (sometimes by a significant amount). Here you can hide plumbing communications.

No right angles when laying a new sewer system. If this condition is not met, installation at an angle of 45° is permitted (two such angles instead of one straight one).

If you install a toilet in an apartment taking into account these simple rules, then the likelihood of a blockage will be minimized (the drains are discharged by gravity).

In practice, to move the toilet you will need to perform a certain sequence of actions:

Mark the distance to which the bathroom can be moved. You will need to secure one end of a one and a half meter twine to the riser and draw an arc with chalk (tied to the other end of the rope).
Select the most suitable location for the toilet and install it. It is advisable not to leave the maximum removal zone marked on the floor.
Measure the height difference between the center of the drain pipe and the floor. Compare the obtained data with the height of the inset point. If it turns out to be higher, you will have to build a podium, with the help of which the drain pipe rises 30 mm above the riser tee (tie-in point).
Secure the plumbing fixtures to the podium (floor) and connect them to the drain system, ensuring that the pipeline is as straight as possible (avoid right angles).

It is not necessary to perform a hard approach cold water to the toilet, it is much easier to use a long flexible hose.

Toilet in an apartment: how to move the toilet from the riser

Creating a comfortable environment is impossible without remodeling the premises, which also affects the toilet in the apartment. Increasing the free space of the toilet

Methods for moving a toilet from a riser to another place

Due to the small area of the bathroom, often when carrying out a major renovation of the restroom, it becomes necessary to move sanitary equipment. In order to effectively use free space, as a rule, many people prefer to redevelop the premises.

The result of this work is the transfer of the toilet from the riser. Since this process is related to issues of water supply and drainage of the device, its decision must be taken as responsibly as possible.

Reasons for moving the toilet

Before we begin the process of dismantling the old toilet and installing a new one, we will consider the main reasons for its removal.

Changing the layout of the bathroom. In this case, all operations are coordinated, at a minimum, with the Housing Inspectorate, State Sanitary and Epidemiological Supervision, State Fire Inspection, and Architectural and Planning Department. Only after obtaining permission is the restroom remodeled. When moving a wall, the old location of the device may cause discomfort, which is why there is a need to move it.
Replacing an old device with a new one, which is much larger. If, due to the dimensions of the updated design, it cannot be installed in its previous location, the product should be moved.
Buying new furniture for the restroom.

Remember, regardless of the motivation, the old toilet should be removed intact, the sewer system should be remodeled, and only after that proceed with installing the device in another point in the restroom. For this purpose, a long flexible liner is often used.

Moving the toilet (easy way)

This method involves moving sanitary equipment over a distance that does not exceed 30cm.

Before proceeding with the installation of the structure in a new location, it is necessary to dismantle the old device.

The sequence of work depends on the method of installing the plumbing.

If the device is fixed using standard fasteners, and its outlet is connected to the sewer with a rubber cuff, you must:

unscrew the screws that secure the toilet to the floor;
pull the outlet of the device out of the socket of the sewer line

Let's consider the sequence of work if the toilet is placed on an adhesive or cement base.

Before dismantling the device, you should turn off the water supply valve to the tank and also drain the liquid from the container.

Remove the putty between the outlet of the structure and the sewer socket.

Remember, the work must be performed as carefully as possible to eliminate the possibility of the outlet breaking, otherwise the device is not subject to further use.

Loosen the toilet. For this purpose, a wide chisel is driven in from different sides of the base of the structure.
Pull the outlet, strictly along the axis, from the sewer socket.

Let's take a closer look at the process of installing a toilet in a new location.

Clean the outlet of the device and the sewer pipe.
Mark new holes in the flooring for mounting the toilet and then drill them out.
Place the corrugation on the outlet of the device; it is important to first apply sealant to the surface.
Cover the gaps between the base and the flooring with cement mortar, this will create additional support for the structure.
Insert the corrugation into the socket.

After performing the above operations, you should check the functionality of the device.

Moving the toilet (the difficult way)

If you need to move the device to a distance that exceeds the length of the corrugation, it is necessary to alter the sewer system.

Installation and dismantling of the device will be similar to the simple method. At the same time, in order to expand the drainage pipeline, a plastic pipe with a diameter of 110 mm is used.

Remember, the length of the structure and the choice of corners depend on the location of the toilet.

Nuances to consider when assembling plastic sewers

Ensure there is a slope towards the riser: 2 cm per linear meter.
When removing the cast iron bend from the tee onto the device, you should first heat the socket using a blowtorch. The result of this procedure is burnout of the bonded seal and cracking of the cement putty. After this, you need to remove the pipe from the socket.

The sewerage system should be installed directly from the riser.

To insert a plastic pipe into a cast iron socket, use a sealing collar.
Cast iron pipe connections filled with sulfur are annealed using a blowtorch.

Remember, in order to minimize labor costs, instead of precisely fitting plastic pipes of the drainage system, you can use corrugation to the toilet outlet.

For the efficient functioning of the sewer system, it is important to take into account the following rules when connecting plumbing equipment.

The greater the distance from the toilet to the sewer riser, the higher it should be located. This will create the necessary slope of the pipe for unimpeded drainage of wastewater.

If the structure is very far from the riser, it is necessary to provide for the construction of a podium.

It is prohibited to attach toilets or pipelines to inter-apartment walls, or to move sewer risers.
Plumbing fixtures should be connected to the main line at an angle of 45 or 135 degrees.

Remember, you cannot connect the toilet to the sewer system at a right angle, as this will inevitably lead to the formation of a pipe blockage.

To be able to carry out preventive maintenance, it is important to provide special hatches in places where the pipeline turns.

Thus, if it is necessary to move the toilet from the riser to a new location, it is important to initially consult with an architect, familiarize yourself with the rules for installing the structure, measure the distance from the sewer system to the device, and only then choose the required method and begin the process of performing the work.

Methods for moving a toilet from a riser to another place

Methods of moving a toilet from a riser to another place Due to the small area of the bathroom, often when carrying out a major renovation of the restroom, it becomes necessary to move

How to properly move the toilet from the riser when combining a bathtub with a toilet?

Good afternoon We are planning a bathroom renovation. We want to combine it with the toilet. To make redevelopment easier, you need to move the toilet. I doubt that this is possible... Is this real? And how to make sure that you do not encounter problems in the further operation of the equipment?

Hello! You can move the toilet some distance from the riser. However, this seemingly simple event has many nuances on which the further use of the equipment depends. Plumbers warn that the greater the distance sewage has to travel through the sewer riser, the higher the risk of a blockage. Some “masters” argue that this is not so, because theoretically, the pollution will “get” to the goal in any case. This is true, but there are much more opportunities to “stay in place” on a long journey.

Another problem is the appearance of an unpleasant sewer smell in the room. It is associated with excessive vacuum, which is inevitable in sewer pipes that are too long. In this case, each flush will be accompanied by the suction of water from all nearby plumbing fixtures and the breakdown of their water seals. In addition to odors from the sewer, there will also be unpleasant gurgling sounds. To avoid the problems described above, you should follow the recommendations of the current SNIP.

In some cases, when moving a toilet from the riser, it is necessary to raise the equipment onto a small podium to provide the necessary slope for the sewer pipes

The document prescribes moving the toilet no more than 1.5 m from the sewer riser. In addition to the “correct” removal, you also need to observe the required slope under which the pipeline should be laid. For parts with a diameter of 100 mm, the slope should be 2 cm per meter. For elements with a diameter of 50 mm, the slope cannot be less than 3 cm per meter. These recommendations should be strictly followed, otherwise problems with blockages cannot be avoided. Reducing the recommended parameters will reduce the speed of fluid movement, which will lead to blockages. Increasing the slope, on the other hand, will cause the water to move too quickly. It will not have time to capture solid contaminants, which will begin to accumulate in the pipe and, over time, completely block it.

It turns out that most often, when moving the toilet to another place, it is necessary to lift it in order to provide the necessary slope for the pipes. In this case, depending on the transfer distance, a fairly decent amount of lift can be obtained. In addition, the pipe connecting the riser and the toilet will also have to be masked somehow. Considering that its diameter is quite large, you may need to raise the floor or equip a small podium specifically for plumbing equipment.

Another one important detail: When laying a new pipeline, right angles must be avoided. If you can’t do without them, proceed as follows: install two 45° angles instead of one 90°. Otherwise, the likelihood of blockages in the pipe increases sharply. All the above requirements are mandatory when moving the toilet. However, even they do not work if it is necessary to move the equipment to a distance greater than that specified in SNIP, or its recommendations turn out to be difficult to implement. There is a solution in this case too.

The first is moving the riser itself, which is extremely troublesome. The second is the use of special equipment that is intended for forced sewerage. It forces the system to work in conditions where conventional gravity sewerage cannot cope with its functions. To equip such a structure, a sololift or fecal pump. This is a compact device that can be placed behind the toilet tank or even inside it. The device, which is a powerful pump equipped with grinder blades, pumps out sewage and grinds solid waste, and the resulting mass is pushed into the sewer.

One of the main advantages of the equipment is the ability to use sewer pipes of small diameter: from 18 to 40 mm, which are very easy to hide even behind plasterboard wall. The pump power is quite high. With its help, you can easily remove sewage to a distance of about 5-7 m vertically and about 100 m horizontally. There are no additional components required for installation of the device. construction works won't be needed. When choosing a sololift for forced sewerage, you need to take into account that if you plan to connect to it washing machine or a shower stall, you need to choose models with relatively high temperature limits for drains. Otherwise, the device will fail very quickly.

Options are available with short-term protection, which allows the pump to pump hot wastewater. However, it is only designed for half-hour operation. Full time job with heated liquid, such devices are also contraindicated. In the technical part, recommendations for moving the toilet from the riser are not much different from standard instructions for connecting the device. The only difference is the installation of a longer pipeline laid at an angle. The installation of the grinder pump is carried out in strict accordance with the requirements of the instructions.

How to correctly move the toilet from the riser - advice from an expert

When remodeling a bathroom, it is often necessary to move the toilet some distance from the riser. Let's look at the problems that may arise and ways to solve them.

Is it possible to move the toilet in the apartment to another place?

Anything is possible, you just have to take it seriously and find out everything. Of course, you can put a toilet in the middle of the room and enjoy life, but if you do the sewerage and drainage incorrectly, then soon the whole room will be empty.

Very important! For every meter of outlet there should be a rise of about 3-4 cm, otherwise the contents of the toilet simply will not drain, etc. Thus, if you move the toilet by 2 meters, then at the base of the toilet the height of the connection should be 7 cm, if by 3 meters, then about 10 cm. Can you afford such a rise? After all, to do this, you need to either put the toilet on a pedestal or raise the floor

Not everything is so simple, from a technical point of view, you can move the toilet anywhere, even to the living room, supply water without problems, but the slope of the pipes cannot be maintained for a length of more than 5 meters, the toilet will simply end up “under the ceiling”, there is a way out forced sewerage.

Technically everything is solved, the problem is different.

Bathrooms cannot be built above kitchens or above the living quarters of neighbors below.

This is the first point that sharply limits the concept of “to another place.”

The other places that remain are the actual Bathroom itself, inside of which you can move the toilet anywhere and the corridor.

A toilet in the hallway is certainly fun, but not very convenient.

There are exceptions if you live on the ground floor and there are no residential or utility premises below you (workshops in the basement, Sport halls etc.), then you can transfer it wherever you want.

Or if you are the owner of a two-level apartment.

In this case, your toilet may well be installed above your kitchen.

You can move the toilet no matter what, and no one will stop you from doing it, but in addition to placing it in a convenient desired place, it needs to be connected to the water supply (this is not such a big problem) and the sewerage here is more complicated!

The plumbing problem can be easily solved; re-soldering the plastic or installing a longer supply hose will not be difficult, but with the sewerage you won’t get much faster; there should be a central riser nearby, since laying a 100 mm pipe or corrugation is too far from aesthetically pleasing, and is also fraught with blockages.

Therefore, a riser is needed, apartments often have them in both bathrooms and storage rooms, and even sometimes in corridors and kitchens, so all adjacent rooms will be within the access zone.

We need to decide, connect and arrange suitable premises- that’s all, if you’re worried about problems with the housing, don’t be afraid, but don’t tell everyone on every corner, otherwise you’ll have to register the redevelopment!

Is it possible to move the toilet in the apartment to another place?

Is it possible to move the toilet from its usual place to a more convenient one? How to do it? What materials will be needed for the operation and what nuances should be taken into account?

Let's try to figure it out.

Why is this necessary?

There can be quite a few reasons for transfer:

Changing the layout of the toilet. If the wall is moved, the old location of the toilet may be inconvenient - too close to the wall or, conversely, not optimal in terms of space utilization.
to another, having different dimensions . If the old toilet was perfectly placed across the combined bathroom, and the new one can only be positioned along it, obviously, the sewer system will also have to be redone to accommodate it.
Purchasing new furniture for the bathroom, washing machine, baths and so on.

Regardless of the motivation, the conclusions in all cases are the same: the old toilet should be removed as intact as possible and, after redoing the sewerage system (and, sometimes, the water supply system), it should be reinstalled at another point in the room.

Advice: in general, it is rarely necessary to run a hard cold water supply to the point where the toilet is new.
If the toilet is moved within the same room, it is often much easier to buy a long flexible hose.

Moving the toilet

Simple case

The toilet unfolds or is moved to a small distance, about a dozen or so centimeters.

Dismantling

Dismantling a toilet greatly depends on the installation method.

If the toilet was mounted on standard fasteners, and its outlet is connected to the sewer with a standard rubber cuff, everything is simple:

Remove the screws securing the toilet to the floor;
Pushing the toilet towards you strictly along the axis of the socket sewer pipe, pull the toilet outlet out of it.

In this case, it is not even necessary to turn off the water to the tank.

If the toilet is mounted on glue or cement, and its outlet is covered with the same cement in a cast iron pipe, you will have to tinker:

Armed with a strong screwdriver or a narrow chisel, carefully remove the putty from the space between the sewer pipe and the toilet outlet. Be very careful: a bad move and you'll have to go get a new toilet.

Once the outlet is released, we will need to loosen the toilet on the floor. A wide chisel is carefully driven, with little force, one at a time from different sides under the base of the toilet. Sooner or later he will swing, announcing that the job is done.
Then, again, we move the toilet towards ourselves, pulling its outlet out of the sewer socket strictly along its axis. If it gets stuck, do not pull harder, but slightly rock the toilet from side to side. Of course, before doing this, it is better to turn off the water to the tank and drain the water.

Installation at a new location

Since the distance to the sewerage system and water supply will be short, we will not need to either remodel the sewerage system or extend the water pipe.

If the old flexible hose is in good condition- We won’t touch her. If it leaks or is not long enough, we simply replace it with an analogue one. The operation is simple and, I think, does not require a separate description.

We will connect the toilet to the sewer with corrugation. This corrugated pipe, in general, has rubber seals on both sides; but it would be a good idea to stock up on silicone.

In addition, you will need a toilet mounting kit.

Important: fasteners must be equipped with plastic washers.
Steel screws should not be pressed directly onto the earthenware.

Clean the toilet outlet and sewer pipe from debris and wipe dry.
Mark new holes in the floor for the toilet mountings and drill them. If there is a tile on top, first pass it with a drill bit along the tile. larger diameter.
Place the corrugation on the toilet outlet, after applying sealant.
Pull the toilet towards the floor. We need him to stop wobbling, nothing more. Seal the gaps between the base and the tiles with cement mortar - this will prevent the lateral force from splitting the base of the toilet, creating additional support for it.
Insert the corrugation into the socket - again on the sealant.
Use it.

As you can see, the result is quite satisfactory. Only the seat is askew

Difficult case

We have already agreed that within small room It is easier to connect water with a long flexible hose. Moving the toilet to a distance greater than the length of the corrugation will be accompanied by alteration of the sewer system.

Dismantling and installation will be the same; in order to build up the sewerage system, it is used plastic pipe diameter 110 mm. The length and selection of corners depend only on the new position of the toilet.

Assembly plastic sewer extremely simple. It is attached to the wall with clamps or laid directly on the floor.

As always, there are a few subtleties.

To insert a plastic pipe into a cast iron socket, use a sealing cuff. It is better to place it on silicone sealant, first of all, thoroughly coating its joint with cast iron pipe.

modern materials

Conclusion

I think the article answered the question of whether the toilet can be moved. Can; Furthermore, there are no particular difficulties in this.

Good luck with the renovation!

Many of us quite often undertake home renovations according to the most various reasons: the need to replace furniture, update old decoration, desire for something new, etc. And most often, renovations are started, oddly enough, in the bathroom. As a result, it may be necessary to move it from the riser to the side. Next we will talk about all the features of this process and will give detailed instructions on how to install a toilet in a new place with your own hands (photo and video instructions are also included).

The process of dismantling the toilet

At first glance, the process of moving a toilet is not complicated, but in reality this is far from the case, since the further you plan to move the toilet from the riser, the higher the likelihood of occurrence. Therefore, the decision to carry out this action must be fully justified.

Most often, the need to move the toilet to another location arises for several reasons:

Changing the layout of the bathroom/expanding its area. Expanding a space usually entails tearing down walls, moving pipes, etc. Which, in turn, often negatively affects the location of the toilet and therefore has to be moved.
Replacing an old toilet. It's about about a toilet that has different dimensions from the old one. In this case, there is simply no other choice but to dismantle the old plumbing.
Purchase new plumbing. This applies to or washbasin, the placement of which will require changing the location of the toilet.

The process of dismantling a plumbing fixture is directly related to how it was installed. The easiest way to dismantle it is when the toilet is mounted on standard fasteners and connected to the tank with a rubber cuff. In other cases, the dismantling process will look something like this:

We dismantle the fastening. You will need it wrench, if the plumbing fixtures are screwed to the floor.
We pull out the outlet with the sewer. Gradually move the toilet towards you along the axis of the socket. It is not necessary to turn off the water; just press the water drain button out of habit.

Advice. If the toilet was installed with glue or cement, it should be pulled out very carefully, since there is a high risk of damage to the structure.

We remove the putty located between the socket and the outlet. Use a screwdriver for this purpose: act very carefully so as not to damage the structure (of course, if you need it).
Using a chisel, carefully loosen the toilet. To do this, you need to carefully drive the tool under the base of the toilet from several sides and then move it from side to side, trying to loosen the structure.
Having loosened the structure sufficiently, we carefully remove the outlet from the socket.

Toilet moving technology

The toilet can be moved not only to different distance, but also install under different angles. Depending on these features, installation can be either simple or complex. Let's look at the process in detail.

Simple case

After dismantling old design you can begin the main work. The first thing you need to do is inspect the old liner: if it is in bad condition or is not long enough, you need to replace it.

Corrugation connection

Immediately before installation we prepare additional elements: corrugation (for connecting the toilet outlet with the socket), steel fasteners (plastic washers are required).

Advice. Even if the corrugation that you plan to use as a connecting element has O-rings, be sure to use silicone sealant when installing it.

So, let's proceed directly to the installation of the structure. Using a drill, we drill holes in the places previously marked for fastenings. If there are tiles on the floor, use a slightly larger drill bit first. Then we carefully clean the connecting elements (bell and outlet) and wipe them dry.

We apply sealant to the corrugation and put it on the outlet. We install the toilet, insert the fasteners and tighten them, acting very carefully. As soon as the structure becomes motionless, we stop tightening the fasteners. If there are any gaps in the floor, we cover them. Then we insert the second part of the corrugation, lubricated with sealant, into the socket.

Difficult case

If you plan to move the toilet a distance that is longer than the corrugation, you will need to remodel the drain. Since the process of installing the structure in this case is no different from the previous one, we will not consider it again. We need to consider in detail another process - sewerage expansion. A plastic pipe is most often used for this purpose. Regarding the length, design features and the number of connecting elements, then everything depends directly on the new location of the toilet.

Sewage pipe

The pipe will be attached directly to the floor or (using special clamps) along the wall. But there are other features that you should pay attention to Special attention. To be able to lower the sewer to the floor level, it is necessary to remove the outlet to the toilet from the cross. In the case of plastic, there should be no problems; it is much more problematic to do the above action with cast iron parts. Before removing the outlet, it is better to warm up the socket blowtorch. This must be done. Otherwise, the sealant will remain, and the putty will most likely crack. If the connecting elements are filled with sulfur, it also needs to be heated with a blowtorch.

Attention! When working with sulfur, it is necessary to wear a gas mask, and the room in which the work is carried out renovation work, must be well ventilated.

After carrying out the above operation, dismantling the pipe and socket will become very simple. And further actions (direct installation of the structure) correspond exactly to the first case.

Possible difficulties and their solutions

After removing the toilet to a greater distance from the riser, certain difficulties may arise, which can be avoided by following simple but effective advice. So, the first and most common problem is the vacuum in the pipes when flushing water from the toilet tank, which, in turn, may well cause a breakdown of the water seal in nearby plumbing fixtures. In addition, this process will be accompanied by unpleasant odors and gurgling sounds.

There is also a high probability of blockages, which is quite logical, since when moving the toilet from the riser, the path of sewage increases. In theory, sewage should “reach” the sewer, but blockage, nevertheless, becomes a more likely problem.

The solution to the above problems is simple: follow the SNiP regulations. According to current rules, it is prohibited to remove plumbing fixtures from the pipe at a distance exceeding 1.5 m.

It is important to install the sewer pipe correctly

Another one of possible problems– insufficient/excessive pipe slope. In the first case, you can provoke a decrease in the speed of drains (which will inevitably lead to blockage), in the second - the accumulation of solid contaminants that will impede the outflow of liquid.

To prevent this, remember a simple rule: for parts with a diameter of about 1 m, the slope should be at least 2 cm per meter; for parts with a diameter of about 0.5 m, the slope should be at least 3 cm per meter.

As you can see, the process of moving the toilet from the riser cannot be called easy. But if you follow all the recommendations described above, you will be able to carry out all the work quickly, clearly and without any difficulties. Proceed carefully and carefully. Good luck!

Toilet installation: video

Moving the toilet: photo

Relocating a toilet is most often done due to the small area of the bathroom. The owners have to use every centimeter of free space to expand the area. In most cases, this particular household toilet item takes up quite a lot of space.

There are too many now design ideas, which are hampered by its location. Therefore, the toilet is deployed or moved to a more suitable place.

Main reasons:

increase usable space premises;
optimization of the bathroom area;
implementation of design ideas;
installation of plumbing equipment for a child.

The main reason for the transfer is to free up useful space in the plumbing room. The owners want to move the toilet in such a way that they can install a washing machine, sink and other convenience items. And simply free space makes the room spacious and comfortable. This is especially true for panel houses, old “Khrushchev” buildings and similar buildings, where the bathroom area has small area or combined with a bathroom.

You will also need to move it when installing the toilet directly opposite the door. This is inconvenient for the use of the entire room and is dangerous for the equipment, since the door hits the toilet body. Ultimately, cracks appear on it, which gradually destroy the toilet. In this case, the owners may suffer additional losses.

A popular reason to move a toilet to another place is to implement design ideas. The ideas of famous designers involve moving equipment closer to the wall or to the opposite corner. This makes it possible to free up room space for the designer’s creative thoughts.

Particular attention should be paid to the children's toilet - a full-fledged plumbing equipment, which is characterized by smaller dimensions and smaller volumes drain barrel. It is best to move such a toilet to the opposite corner.

Moving the toilet - possible risks

This type of work is associated with significant risks that the owners take on:

increase in length water pipes coming to the toilet;
increased likelihood of blockages;
change in pipeline slope;
the appearance of right angles in the water supply system;
violation of standards.

Even if the toilet is moved close to the wall, it must be taken into account that an increase in the piping system leading to this equipment can lead to problems. For example, when flushing water, a vacuum is formed, which will lead to the breakdown of the water seal in all plumbing located near the equipment. The process is accompanied by loud gurgles and unpleasant odors.

For the same reason, blockages appear. After all, the pipe leading to the toilet has increased in length. This creates conditions for higher concentration sewage To avoid these phenomena, it is necessary to comply with the requirements of SNiP ( building codes and rules). With this approach, you will not only reduce the likelihood of breakdowns to a minimum, but also save your health and money.

When calculating the required pipeline slope, you should take into account the standard, which states that for all elements with a diameter of 100 mm, the presented indicator must be at least 2 cm per meter. If there are parts with a diameter of 50 mm, laying should take place at a minimum slope of 3 cm per meter.

A reduced slope value slows down the movement of wastewater and provokes the formation of stagnation of sewage in the pipeline.

A large slope is also undesirable. In this case, water will flow at an increased speed, which will lead to the appearance of solid contaminants. The gradual accumulation of such formations will increasingly impede the flow of water, leading to clogging of the pipeline.

Compliance with SNiP is a key factor in the success of relocating a toilet. But when transferred by more than 1.5 m, these recommendations cannot be taken into account. If there is such a task, you need to install . This is also true at a shorter distance, if there is no desire or opportunity to work on adjusting the slope and installing additional pipes.

Various options for moving the toilet from the riser

Moving the toilet from the riser can be done in two ways:

moving equipment at a distance of 10 to 20 cm;
moving equipment over long distances.

Before starting work, it is necessary to take all the necessary measurements and dismantle the toilet. These are mandatory measures that will allow you to successfully move plumbing equipment to Right place and distance.

Moving the toilet to a distance of 10-20 cm

In both cases, it all starts with dismantling the plumbing equipment. A complication here may be that the toilet is installed on cement or glue and its base is also coated with cement. Movements should be as smooth and accurate as possible. Otherwise, cracks will appear on the device, which will render it completely unusable.

If the device needs to be moved a short distance within 10-20 cm, then you need to shut off the water supply to the unit and perform the following steps:

clearing the space between the sewer pipe and the base of the equipment from putty (a strong screwdriver or chisel is suitable for this);
carefully loosening the toilet (in different places a wide chisel is hammered into the base, the operation is repeated until the device begins to wobble);
lifting the toilet is carried out as follows: pull the device towards you and remove the outlet from the socket of the sewer pipe (this should be done strictly along its axis), if the equipment is stuck, it is forbidden to pull with great effort, it is recommended to carefully swing the device and pull again.

Please note that all dismantling activities must be carried out as carefully as possible using working tools. The toilet must remain in working condition for proper subsequent installation in another location. The standard fasteners and connection of the device to the sewer make the work easier. The device is usually secured with several screws.

To dismantle it, it is enough to unscrew them and carefully remove the equipment from the mount strictly towards you along the axis of the pipeline. Next, it remains to remove the trigger.

Next you should do preparatory work for installation of equipment at a new location. It all starts with a thorough inspection of the old flexible wiring. If it leaks or is not long enough, it must be replaced with a suitable analogue. If no defects are found on the part, we leave it for further use.

To connect the outlet of the device to the sewer socket, you should use a corrugation with two seals installed at its ends. To ensure greater reliability, it is recommended to fill the connection with sealant. Next you need to prepare the fastenings. If they are made of steel, you should make sure that they are not pressed against the sanitary ware. For this reason, plastic washers should be installed.

Precise markings are made on the floor where the fastening will be carried out. Next, the required holes are drilled. If work in progress with tiles, this material is drilled first (the diameter of the drill for tiles must exceed the similar parameter of the drill for concrete).
Cleaning the sewer pipe and toilet outlet. These items must be completely clean and dry.
Apply silicone sealant to the inside of the corrugation and secure it to the outlet of the device.
Installing the toilet in its proper place, securing the fasteners in advance drilled holes followed by tightening.
Gaps may occur between the floor and the equipment. They should be thoroughly covered with the solution. This also creates additional support, which will prevent the base from collapsing under the influence of lateral forces.
Lubricating the other part of the corrugation silicone sealant with its connection to the sewer pipe.

How to move a toilet over a long distance

To move the toilet to a distance exceeding the specified parameter, you should prepare for alteration of the sewer system. To do this, we need to expand the sewer system. In most cases, a plastic pipe with a diameter of 110 mm is used for this. The length, number and configuration of auxiliary elements depend on the installation location.

The plastic pipeline can be mounted on the floor or on the wall using clamps. To lower the sewer to the floor level, remove the outlet to the plumbing equipment from the tee or cross.

If the owners deal with plastic, performing such procedures will not be difficult. It is better to heat cast iron elements with a blowtorch or gas burner. This is done so that the cement putty spreads and the seal burns thoroughly.

If the connections are filled with sulfur, they also need to be heated with a lamp. At the same time, they stand out very unpleasant odors. For safety, you should perform the procedure wearing a gas mask in a well-ventilated area. If everything is done correctly, removing the pipe from the socket will be easy. Next, you have to perform a number of standard actions to dismantle and install the toilet.

If the task is simply to turn the toilet at any angle, you must use a tee, corner pipes or corrugation. In the latter case, the work is simple, but the connection system will not last long. In addition, contaminants may periodically appear in the corrugation cavity, which must be removed.