Unusual DIY photo frame decor ideas. Beautiful decor for photo frames with your own hands DIY carved wood frame

Hello, friends! The HeARTwood channel released an episode about how to make a wooden frame using a simple device. First, let's look at a simple way to make spring ties for gluing small frames.

To work, you will need either a Chinese drill or an angle grinder.
The grinder is convenient, it is always at hand. The main material will be a spring. It is desirable that she be from thin wire. That is, it should not be very stiff, or you need a powerful spring. It is advisable to turn it round to round, but if it is a little stretched, then that’s okay too.

Steps to create a frame

You need to saw off the small half rings with a grinder. If the wire thickness is small, wire cutters are suitable, but it is not certain that they will hold up, so it is better to use a grinder.
Cut the rings so that there is not a whole ring, but about three quarters. We cut 8-10 such parts. It is not necessary to adhere very strictly to the size, the main thing is that you get rings.
If the spring is not compressed, you will have to straighten the coils with your fingers or pliers. The plane must be maintained.
We sharpen one side on the disk first, then the other. You will get some kind of cloves.
This is what the finished ring looks like.

Now we’ll make a few pieces and see how they work. To do this, take an oak strip, cut 4 parts, and assemble a small frame.
We take the ring, hook it on one side, pull it to the other, and fix it. Let it dry.
The big advantage of such small brackets is that you can install them by hand, you can put several pieces if you need more force.
The clamps are very simple to make, easy to use, and easy to install and remove. They are good to use on large vascular wood, for example, on oak they leave dots. They are not that noticeable. But on soft and finely vascular wood it will be a little noticeable. In principle, if you sand it a little, then these points will not remain.
So, the frame is glued together and the half rings helped with this. The big plus is that they are made in literally a couple of minutes and are very convenient and functional to use.

Frames for photos and paintings from standard lining

The cost of one 40x50 linden frame is 38-42 rubles (depending on the cost of packaging the lining). Pine will cost half the price, but there will be a lot of unpresentable knots.
It took one pack of lining to produce 20 frames. One board makes 2 frames, and a standard pack contains 10 boards 2 meters long. Dimensions 40x50 - “internal” correspond to the size of the painting. The external dimensions of the frame are larger, so the trimmings were minimal, solely due to cutting the corners.
Cut the boards in cross section as follows:

The actual production of the frames took about 2 hours of work: Trimming the blanks. Gluing the frames with standard PVA wood glue (fixing the corners with a stapler on the reverse side).
It took two days to dry, then about another hour was spent tinting the frames with a wood glazing compound, and that’s all...
The frames turned out to be quite good, they look a little brutal, but for oil painting, as an option, they are quite suitable...

You can, of course, make frames from ordinary boards, but the labor costs will be much higher.
zen.yandex.ru

How to make a wooden frame with your own hands

Nowadays, homemade interior items are in great demand. Many stores have appeared selling goods of this category. Handmade products look original; the authors put in not only imagination and skills, but also a piece of their soul. And it’s nice to have in your home not standard products from consumer goods, but an individual product, which is in a single copy. However, for such products you will have to pay a tidy sum, since authorship is valued at a high price. It will be much cheaper if you show creativity, imagination and realize your vision of a household item, for example: photo frames, paintings, wooden mirrors.

Creative plans

Before starting any work, you always need to draw up a rough plan of action, prepare materials and the item you want to frame. Ready product should fit organically into the interior of the room, be it an office or residential apartment. The frame cannot fail to match the style general interior. Also, the materials from which frames are made vary greatly in texture, quality, color scheme. The wooden frame itself can be in a simple style, or it can be with beautiful openwork carvings.

Even a simple, even frame made of wood is complemented with design elements that will give it a special style and originality. You also need to decide what exactly to focus on in your work. If the main thing in the project is the design of a finished frame, then it can be purchased in a store and transformed into a masterpiece at home. If the frame itself becomes the object of creativity, then it is better to make it yourself.

Selection of materials

In order to make a frame with your own hands from wood, select required wood. Basically you need to look at the pattern and structure of the tree, since, in principle, any species is suitable for this. If the frame will be painted later, then the simplest one is chosen - pine or spruce. If the structure of the wood is visible and the product is subsequently coated with varnish or stain, then you need to take wood with an original pattern. Walnut, ash, cherry, and linden look very beautiful.
Beautiful frames for paintings with your own hands made of wood are created when carvings are applied to them (floral, plot or simple ornament). For carving, use softer wood, especially if the carver is a beginner. Professional, of course, and oak board will make a pattern, but for a beginner it will be difficult, since oak is considered a very hard tree. You will also have to buy a set of cutters of different sizes.

Another option for making a frame with your own hands from wood is a simple wooden product, which is decorated on top with improvised materials. Nowadays, picture frames decorated with something unusual are fashionable. These can be pieces of bark, pencils, shells, buttons and other waste material.

Making a wooden frame

Before making a picture frame from wood, you need to prepare following materials and tools:
plywood or fiberboard;
wooden slats, plinth or baguette;
hand saw or jigsaw;
miter box;
construction stapler;

PVA glue;
acrylic varnish or paint, brushes;
stain (if necessary);
plastic or metal loop;
nails or screws;
hammer or screwdriver (as a last resort - a screwdriver);
corner clamps;
sandpaper.
When planning to cover a picture frame with something (it’s easy to make one from wood with your own hands), prepare the material that is needed for this. You can lay out the required pattern on the table in advance to understand how it will look.

Step-by-step instruction

The first step is to measure the size of the painting and cut out a square or rectangle from plywood or fiberboard. Its size should be larger than the picture by the width of the wooden slats. Having attached a picture or photograph to the plywood, outline it with a pencil so as not to stain the object while working. The painting can then be put aside until the work is completed.

The second step in making a frame from wood with your own hands will be cutting the slats at an angle of 45 degrees. To do this you will need a saw and a miter box. A strip or block of wood is inserted into the miter box and sawed off along the line. Then we repeat the procedure with another bar. We combine the corners of two pieces of wood, you should get a right angle of 90 degrees. We apply this angle to the plywood and mark the length of the other sides. After this, using the marked marks, we make cuts in the other two corners. We attach the assembled frame to the plywood and check its size. If everything comes together clearly, you can proceed to the next stage.
The ends of the slats, cut at 45 degrees, are coated with PVA glue and tightly tightened with corner clamps, left alone until completely glued (approximately 2 hours). After this, for better fastening, connect the corners of the slats with staples using a construction stapler.

Assembling a wooden frame

The last stage of making the frame will be fastening the parts together. There is a small nuance here. If you are attaching a painting or photograph permanently, you can glue it to plywood. Then everything is much simpler. The finished frame just needs to be nailed to the plywood or fastened with small screws. If the photo is inserted, then you will have to work extra hard.
In order for the photo to fit freely into the frame, you must leave a gap between the frame and the photo. In a purchased frame, wooden slats are processed to milling machine and a step is made for insertion. Not everyone has a router at home, so you need to do it differently. Make an additional layer between the frame and the plywood, for example from thick cardboard. Strips are cut to size corresponding to the width of the frame and glued along the perimeter of the plywood on three sides. There is no need to do this from above. A painting or photograph will be inserted into that slot.

Further sandpaper clean the surface and cover with a layer of varnish or paint. After drying, repeat the cleaning procedure and cover with another layer. Let dry. Acrylic varnish dries quickly and produces almost no unpleasant odors.
It doesn't take long to make a picture frame with your own hands from wood. All that remains is to attach a loop and hang it on the wall. The only thing I can recommend is to laminate the photograph so that you can periodically wipe off dust without damaging the photograph itself.

Variety of materials

You can create frames with your own hands from wood and metal, baguettes and plastic, polyurethane skirting boards and simple branches. Nowadays there is such a free approach to the choice of materials that any flight of fancy can be realized. The frames are roughly knocked down with large nails, tied together from randomly sized branches, and burned blowtorch, peel off with a stiff brush. Everyone has their own approach. Whoever thinks of something will realize it in his work. Nowadays there are so many various materials and examples of other designers that you can, after looking at the photographs, choose the one that suits you.

Designer frame for mirror

Frames can be made not only from slats or bars. Let's consider several options for unusual frames. For example, how to make a frame for a mirror out of wood with your own hands using small twigs? To do this, we take plywood and cut out a figure several centimeters larger in diameter than the mirror.

If, for example, it is round, then a larger circle is drawn, etc. Then the mirror itself is glued to the center of the plywood circle using liquid nails. A strip of plywood remains along the edges, which we will decorate. To do this, take wood glue and, in turn, coat each branch with glue and place it in a circle with the end in the middle. The work is meticulous and long, but the result will be a completely original thing.

Frame of twigs

Let's look at another example of an original photo frame. Anyone can make it from wood with their own hands. A photograph is glued to a sheet of plywood and a few centimeters of margin are left to the edges to decorate the frame. Branches of the same or different lengths are collected, thoroughly dried and treated with an antiseptic.

After this, you can cover them with acrylic varnish, or you can leave them untouched. Take a beautiful twine and make four bundles from an equal number of branches. The bundles are tightly connected to each other. The result is a frame of twigs, which is then glued to the free part of the plywood sheet.
Come up with your own version, create, search, try, and everything will work out! Good luck!
fb.ru
Another article on the same topic.

Creative plans

Before starting any work, you always need to draw up a rough plan of action, prepare materials and the item you want to frame. The finished product should fit organically into the interior of the room, be it an office or a residential apartment. The frame cannot but match the style of the overall interior. Also, the materials from which frames are made vary greatly in texture, quality, and color. The wooden frame itself can be in a simple style, or it can be with beautiful openwork carvings.

Even a simple, even frame made of wood is complemented with design elements that will give it a special style and originality. You also need to decide what exactly to focus on in your work. If the main thing in the project is the design of a finished frame, then it can be purchased in a store and transformed into a masterpiece at home. If the frame itself becomes the object of creativity, then it is better to make it yourself.

Selection of materials

In order to make a wooden frame with your own hands, the necessary wood is selected. Basically you need to look at the pattern and structure of the tree, since, in principle, any species is suitable for this. If the frame will be painted later, then the simplest one is chosen - pine or spruce. If the structure of the wood is visible and the product is subsequently coated with varnish or stain, then you need to take wood with an original pattern. Walnut, ash, cherry, and linden look very beautiful.

Beautiful frames for paintings with your own hands made of wood are created when carvings are applied to them (floral, plot or simple ornament). For carving, use softer wood, especially if the carver is a beginner. A professional, of course, will make a pattern on an oak board, but for a beginner it will be difficult, since oak is considered a very hard tree. You will also have to buy a set of cutters of different sizes.

Making a frame with your own hands from wood

Before making a wooden picture frame, you need to prepare the following materials and tools:

plywood or fiberboard;
wooden slats, plinth or baguette;
hand saw or jigsaw;
miter box;
construction stapler;

PVA glue;
acrylic varnish or paint, brushes;
stain (if necessary);
plastic or metal loop;
nails or screws;
hammer or screwdriver (as a last resort - a screwdriver);
corner clamps;
sandpaper.

When planning to cover a picture frame with something (it’s easy to make one from wood with your own hands), prepare the material that is needed for this. You can lay out the required pattern on the table in advance to understand how it will look.

Step-by-step instruction

The second step in making a frame from wood with your own hands will be cutting the slats at an angle of 45 degrees. To do this you will need a saw and a miter box. A strip or block of wood is inserted into the miter box and sawed off along the line. Then we repeat the procedure with another bar. We combine the corners of two pieces of wood, you should get a right angle of 90 degrees. We apply this angle to the plywood and mark the length of the other sides. After this, using the marked marks, we make cuts in the other two corners. We attach the assembled frame to the plywood and check its size. If everything comes together clearly, you can proceed to the next stage.

The ends of the slats, cut at 45 degrees, are coated with PVA glue and pulled together tightly and left alone until completely glued (approximately 2 hours). After this, for better fastening, connect the corners of the slats with staples using a construction stapler.

Assembling a wooden frame

In order for the photo to fit freely into the frame, you must leave a gap between the frame and the photo. In a purchased frame, wooden slats are processed on a milling machine and a step is made for insertion. Not everyone has a router at home, so you need to do it differently. Make an additional layer between the frame and the plywood, for example from thick cardboard. Strips are cut to size corresponding to the width of the frame and glued along the perimeter of the plywood on three sides. There is no need to do this from above. A painting or photograph will be inserted into that slot.

Next, clean the surface with sandpaper and cover with a layer of varnish or paint. After drying, repeat the cleaning procedure and cover with another layer. Let dry. Acrylic varnish dries quickly and produces almost no unpleasant odors.

It doesn't take long to make a picture frame with your own hands from wood. All that remains is to attach a loop and hang it on the wall. The only thing I can recommend is to laminate the photograph so that you can periodically wipe off dust without damaging the photograph itself.

Variety of materials

You can create frames with your own hands from wood and metal, baguettes and plastic, polyurethane baseboards and simple branches. Nowadays there is such a free approach to the choice of materials that any flight of fancy can be realized. The frames are roughly knocked down with large nails, tied together from randomly sized branches, burned with a blowtorch, and stripped with a stiff brush. Everyone has their own approach. Whoever thinks of something will realize it in his work. Nowadays, there are so many different materials and examples from other designers that you can look at the photographs and choose the one that suits you.

Designer frame for mirror

If, for example, it is round, then a larger circle is drawn, etc. Then the mirror itself is glued to the center of the plywood circle using liquid nails. A strip of plywood remains along the edges, which we will decorate. To do this, take wood glue and, in turn, coat each branch with glue and place it in a circle with the end in the middle. The work is meticulous and long, but the result will be a completely original thing.

Frame of twigs

Come up with your own version, create, search, try, and everything will work out! Good luck!

Master class “Wood frame for photos and paintings”

"For a family photo." Master Class

Zhbanov Alexander Semenovich, teacher of fine arts and technology, MBOU "Perkhlyaysksya OOSH" of the Ruzaevsky district of the Republic of Mordovia.
Purpose: Regardless of the style of our interior, wooden frames are the best decoration for paintings or photographs, because wood is the most expensive and exquisite material. Thus, a wooden frame can not only decorate a picture or photo, but also improve the design of our interior. A gift in the form of a frame made of wood will bring warmth and comfort to your home.
The master class is designed for 6th grade students; it will be useful for technology teachers when studying the topic “Artistic processing of wood products,” and for creative parents.
Target: Making wooden frames for drawings, photos and paintings.
Tasks: To familiarize yourself with the types of artistic processing of wood products, improve skills in working with wood, and develop creative thinking, develop the ability to see beauty, cultivate hard work, interest in arts and crafts.
Teacher's opening speech
Artistic processing of wood products is an amazing art and skill of working with wood. However, with desire, a little creativity and patience, almost anyone can succeed. interesting items decor. The main types of artistic wood processing are: wood carving, pyrography - burning wood, turning - turning various products from wood, painting on wood. Some means are also provided for wood processing. The most accessible and inexpensive are stains, beeswax, water-soluble paints, varnishes. This simple set of tools will give the product a finished look.
Today we choose simple carving elements and water-soluble paints. But first of all, we need to manufacture the product.

During the manufacture of a wooden frame, we will work with tools such as a hacksaw, hammer and chisel, and perform simple wood carving techniques. Let's practice connection techniques wooden parts using glue, let's do it decoration products. When working, we will strictly follow all the safety rules learned earlier.
To work you will need:
1. Wooden slats 250x50x10mm - 2 pcs., 350x50x10mm - 2 pcs.
2.Wood cutters
3.Watercolor paints, varnish
4.Sandpaper, glue

We chamfer (round) the edges of the slats. We use a cutter or an ordinary knife. Don't substitute left hand under the cutting tool!

Let's prepare all four slats.

Let's draw arbitrary wavy lines.

We cut out a shallow groove (stream). For those who have not used wood cutters before, I advise you to attend this master class. Here you will find the tricks and rules safe work. /blogs/jbanov-aleksandr/obuchenie-tehnike-rezby-po-derevu.html

Let’s make one “bank of the stream” flat.

It turns out to be a stream with one steep bank.

On one half of the slats (with a steep edge) we apply random grooves with an angular cutter, thereby imitating the bark of a tree.

This way.

All four slats are ready.

Let's study this drawing. Dimensions in millimeters.

Let's arrange the slats according to the drawing. Depending on the size of the photo or painting, the size of 50 mm can be reduced or increased. The cut end of the batten is placed on the clean surface of another batten and the location for the groove is marked with a pencil.

Use a fine-toothed hacksaw to make cuts (to the middle)

Cut out the grooves. This is done with a chisel or a flat chisel.

Thus, we get four grooves on the uncut ends of the slats.

Let's put it in places.

Turn it face down and mark the ends of the slats with the corresponding numbers.

We repeat the same work on the reverse side.

You can check it.

It's time to use wood treatment products. We chose ordinary watercolor paints. Everyone has the right to choose the color themselves.

Let's go over it lightly with sandpaper.

Let's assemble using glue. The brand of glue can be different: carpentry, “Moment”, “PVA” and others. Coat the grooves with glue and press tightly. You can use a simple press (several books on top of each other)

The frame is almost ready to be used for a painting. And for photography you need glass so that the photograph is well preserved and can be easily replaced. To do this we use a window glazing bead.

On the reverse side, we frame the inside of the frame with a bead, retreating 6-8 mm from the edge. You can use glue or small nails.

From the same glazing bead we will make two small turntables.

Let's score

Let's give an aesthetic look

Cut a rectangle to size (thick cardboard, plywood, fiberboard)

All that remains is to come up with a device for the suspension. To do this, we will make two loops from the wire.

Using an awl or a thin nail, we drill shallow holes and “plant” them with glue.

Let's tie a secure thread

The teacher cuts glass. Paint it with clear varnish. The frame is ready!

Insert a photo.

Gift for a “wooden” wedding.

Today, there is a wide variety of ready-made photo frames in stores. But sometimes there is a desire to do something yourself so that the product turns out to be truly original.

How to make a photo frame

The process of creating a photo frame from wood with your own hands is quite creative. Therefore, different methods are used to obtain the final result.

DIY wooden photo frame.

First way

Least labor intensive and easy to use.

First of all, you need to choose the right fittings from which the future photo frame will be made. To make a wooden frame, you will need wooden slats, glue, paints, sandpaper, and staples for a stapler.
Of course, it’s also worth paying attention to what size the future frame will be. Next, the same length of all four sides of the future product is correctly measured. After which the edges of the slats are filed at an angle of 45 degrees.
Then, using staples, the two sides of the frame are connected, so that the joint becomes barely perceptible. But this is not enough; the sides of the future frame should be coated with glue before connecting them with staples.
After the glue has dried, you can start decorating the frame. In this regard, everything will depend on your own wishes and imagination.
Having decorated the frame and gluing the selected ones to it decorative elements, you can put a photo in it. This can be done using a stapler, and the photo must first be laminated. This will allow you to maintain its appearance for as long as possible.

Second way

The next method is more labor-intensive, although the initial principle of operation is the same as in the first case. But this version of the frame requires the presence of a baguette. First of all, stick together wooden blocks identical sizes, then the same bars are glued together, but smaller in size, for the second frame. The result is an object that looks like a box.

Decor elements wooden photo frame can be very diverse.

The joint that connects the two frames is glued decorative baguette. It is coated with glue twice before use. After drying, the wooden frame can be painted at your discretion. The result is an unusual and original product.

An item made with your own hands always brings more joy and satisfaction than something bought in a store. For example, a picture frame assembled with your own hands will always evoke more positive impressions.

A frame with your own hands can also be made using a special woodworking machine, where you can cut out beautiful patterns and create an unusual ornament. But this is usually done by craftsmen who have experience in this type of work.

Wood photo frame

A wooden frame will always win among others with its appearance, and plus, environmentally friendly materials. And any photo in it will look harmonious. When the question arises of how to make a frame out of wood, you should understand that, no matter which version of its manufacture is chosen, it is the end result that is important.

Original do-it-yourself wooden photo frame.

Very often, in order to make a frame, they use in a simple way tightening it with a rubber band. That is, a tape tied in a loop glues together wooden blanks that must be sawed at 45 degrees. True, it is not always possible to complete such work the first time, since it requires certain skills.

Another method can be used. It requires a square sheet of plywood, along the edges of which beams are screwed. They should be located at an angle of 90 degrees. With their help, already prepared elements of the future frame are pulled together and glued together. After tightening, you need to check how the corners of the frame are located relative to each other.

If you want to make a wooden frame with your own hands, then you can explore several manufacturing options and choose the one that suits you. At first glance, it is easier and faster to buy a ready-made wooden frame in a store, but in fact it will not be difficult to make such a product, and of the required dimensions (even non-standard ones), and you can decorate the frame to your liking. If you have a large collection of photographs at home that you plan to hang on the wall, you will need a lot of frames, and this will cost money. The way out of the situation would be self-production framework

Wooden frames can be made using simple tools or using a woodworking machine. The finished frame can be decorated with skillful carvings or a beautiful ornament can be burned out. Such products can be done by craftsmen, but it is better for beginners to try their skills on the example of a simple wooden frame made of smooth planks or slats.

Simple wooden frame

To make such a frame you will need: smooth wooden planks, a ruler or tape measure, a saw, a miter box, a plane if necessary, a simple pencil, staples for a stapler, thick cardboard or a piece of fiberboard, metal clips, twine, sanding paper, paint, varnish and decorative elements for frame decoration.

The procedure for making a wooden frame

Estimate the dimensions of the frame and select transverse and longitudinal wooden planks. You can cut a wooden strip into four elements. All parts of the future frame should be as smooth as possible, so if necessary, they can be planed and then treated with sanding paper.
Saw off the ends of the wooden planks at an angle of 45 degrees. To ensure that the corners are even and the product comes out neat, it is better to use special device– miter box with suitable connectors.
The ends of the planks are greased with PVA glue and pressed tightly at an angle of 90 degrees. To fix the corners, the frame should be tied tightly with twine, making sure that the corners do not move. Can be used to secure the corners of half staples from a stapler. They are cut into two L-shaped halves. Next, these corners are inserted into the middle of the cuts at the ends wooden slats, and then the two sides of the frame are connected.
The PVA glue hardens for 15-20 minutes, and after that the frame is again treated with sandpaper and coated with paint or varnish. You can use stain or potassium permanganate, which also gives wooden products beautiful brown shade.
The reverse side of the frame is cut out of thick cardboard or a piece of fiberboard. If the design is not intended to be collapsible, then you can glue the back side to the frame with glue, and for a collapsible frame, use special metal clips.

Wooden frame with passe-partout

This frame is well suited for decorating photographs, as it will emphasize the expressiveness of both color and black and white photographs. Before you start making a frame, you need to carefully consider not only the size of the frame, but also its pattern, as well as the color of the mat.

This decorative frame is made of wooden planks and thick cardboard (for passe-partout). Profiles for a wooden frame can be very different - smooth, with carvings or patterns; the type of passe-partout also varies - thickness, color of cardboard, its pattern. In this regard, you can choose frame details that will be in harmony not only with the photograph or painting itself, but also with the entire interior of the room. This is especially true if you plan to hang several paintings - they must be combined with each other. For example, on dark walls or surfaces of rich color, light wooden frames look good. Accordingly, on light walls you can hang paintings and photographs in dark frames.