Do-it-yourself summer shower for a summer house from scrap materials. Do-it-yourself country shower. Photo instructions for a summer shower on a plank base

Did you work for suburban area or relaxing - this is not so important; in any case, you will certainly want to take water procedures at the end of a long summer day. In order to have this opportunity, you need to build a shower in your dacha with your own hands.

General steps

Regardless of what type of country shower you prefer to build, some steps will need to be completed in any case:

Selecting a location

Choice optimal site for development is accompanied by the following rules:

No shadow. Sun rays are a natural and free source, and if it is not equipped compulsory system temperature increase, then the only one. Therefore, try to provide them with sufficient access to the structure by choosing an open area for the shower.

Presence of drainage or waste pit. Used water must drain somewhere, and it is better to take care of this in advance than to wait for it to find its way into flower beds, a cellar or other undesirable place for moisture accumulation.
Compliance with the overall design. You should not place a shower in front of the facade of the house if it has already been built, or in other no less significant places where it will interfere with general interior. This is especially true for temporary buildings that are not particularly aesthetically pleasing.

Design

Ready-made drawings and dimensions of a shower in the country with your own hands can easily be found on the Internet. You can also create your own unique project yourself.

The main thing is that the do-it-yourself drawings of a shower at the dacha are provided with all the necessary dimensions and a list of materials used.

Option No. 1: film construction

If your suburban area is rarely visited, then build capital construction makes no sense, and for reception water procedures A simple film structure will do just fine, with a number of advantages:

pros

Minimum selling price. You won't need a large number of expensive materials.
Ease of construction. You can easily and quickly cope on your own.
Possibility of dismantling.

Here we can immediately highlight two positive points:

If necessary, such a shower can be moved to a new, more suitable location.
For the winter, the structure is dismantled and hidden in a warm place. dry room, where he will not be threatened by any aggressive weather, nor the danger of being stolen.

Minuses

The negative aspects here are no less obvious than the positive ones:

Unprepossessing appearance. Racks covered with film do not represent any particular aesthetic value.

Low level of comfort. The simplicity of the design does not allow the implementation of many useful functions inherent in capital showers.
Fragility. If you do not hide the film shower for the winter, then in the spring you will most likely have to build a new one.

Installation

So, if you, having weighed all the pros and cons, decided on this economical option, then you will need it step-by-step instruction for a shower for a garden with your own hands:

At the selected location, remove the top layer of turf and level the area. From there we dig a small drainage trench to the drainage system.
We take four metal corners 2.5 m long and eight 90 cm long. As an alternative, you can use wooden beams, but dismantling them will be more difficult.
We drill holes along the edges and connect them with bolts into a quadrangular frame.

We cover it with film, leaving one side partially loose so that you can move it aside to get inside.
We put a regular wooden grid on the floor as a pallet.
We install a suitable water container equipped with a watering can on the roof.

Tip: it is convenient to use a portable shower bag to maintain a temporary structure. It is easy to operate, does not require a reinforced base, is easy to clean and most often has its own heating system.

Option No. 2: frame building

This type of shower is a kind of intermediate option between a film structure and a permanent one. brick building. Such a building is perfectly protected from wind and precipitation, capable of spending the winter under open air without losing its stability, and is equipped with such pleasant little things as shelves for shower accessories and hooks for clothes. But without careful care it will not last long.

In this case, the progress of work is expanded with some activities.

Pouring the foundation

Because frame construction Since the soul for a dacha presupposes its constant presence in one place, it must be equipped with a suitable foundation in order to avoid further subsidence into the ground:

We remove a ten-centimeter layer of earth with an area corresponding to the future structure. It is noteworthy that in this case it is not at all necessary to limit yourself to dimensions of 90 by 90 cm; you can build a more spacious structure, in which there is even room for a locker room.
We tamp the bottom and line the sides with pieces of plywood as formwork.
Knead concrete mortar using the following ingredients and their proportions:

In the place where the drain will be located, we place a small log wrapped in roofing felt. This way we will create a hole through which we will lay it later.
Fill the prepared area with the mixed mixture.
We deduce the slope of the surface towards the drain.
We are waiting for complete setting.

Frame

The assembly of the frame is slightly different from the option discussed above. The only exceptions are big sizes and the presence of central horizontal crossbars at a height of about a meter, which are necessary to enhance the mechanical resistance of the entire structure.

Advice: vertical racks can be concreted during the process of laying the foundation. This will increase the reliability of the design.

Sheathing

The following materials can be used to fill the walls:

Wood treated with antiseptics.
Chipboard.
Plexiglas.
Polypropylene panels.
Iron sheets.
Slate.

All elements are securely screwed to the “skeleton” of the shower using bolts.

A single-pitched roof covered with metal tiles, roofing felt or slate will be sufficient.

Option No. 3: capital structure

The capital shower project at the dacha is an independent architectural structure, which must be registered with the relevant administrative institution. This already suggests the need for such a design.

In addition, in this case, bricks are usually used to build walls, which you need to know how to lay, a reinforced foundation that requires additional costs, and a massive roof that can withstand any precipitation for a period of time. for long years. And when you build a residential building with a built-in bathroom, then the need for such a solid building will disappear, which will cancel all the effort invested in it.

Conclusion

A shower in the country is necessary, but it’s up to you to decide what type of structure to build for this purpose. You can get by with a temporary building or create something more durable, it all depends on your future plans for the site.

The video in this article will introduce you to additional materials. The dacha visited must have all the necessary living conditions, including shower.

It’s hard to imagine a comfortable life without a country shower country holiday. Thanks to it, staying at the dacha becomes much more pleasant, especially in extreme heat.

Making it is not so difficult if you use moisture-resistant material that is easy to install. It could be cellular polycarbonate, plastic panels or corrugated sheets. If you need best option— it’s worth paying attention to showers made of corrugated sheets.

Advantages of a country shower made of corrugated sheets

1. Cheapness. Firstly, if you decide to make a shower from corrugated sheets with your own hands, you save money on all installation work. Secondly, the material itself is quite inexpensive. Thirdly, often after various construction work There are sheets of corrugated sheets left that are a pity to throw away - but here they will come in handy.

2. High strength and the rigidity of galvanized sheets of material guarantees excellent properties to the walls and roof of the future shower.

3. Anti-corrosion properties- this is very important for a room where high humidity is expected.

4. Simplicity installation work , since it is not necessary to have a complex professional equipment and relevant skills.

5. Design speed and installation - four to five hours is enough. Then you need to wait until the sealant has dried, and you can begin to fully operate your small architectural structure.

6.Durability designs.

7. Aesthetic appearance thanks to modern processing material and variety of color palette

This is what a country shower made of corrugated sheets looks like in detail:

We build a shower from corrugated sheets

The whole technology is based on fastening corrugated sheets to a pre-fabricated frame (from profile pipes and angles). To build Summer shower from corrugated sheets with your own hands, you need to prepare the following materials before starting work:

corrugated sheets;
pipes for the frame (50x50 or 40x60 mm);
fitting;
convenient shower head;
hose;
self-tapping screws;
sealing tape, sealant.

You will also need tools such as a mounting clamp, a level and a shovel. It's better to choose quality materials, and not the cheapest ones. Then in the future you will enjoy all the benefits of using modern building materials. With their help, you can quickly and easily make an excellent shower from corrugated sheets with your own hands.

You just need to follow the instructions below and as a result you will get a presentable summer shower made of corrugated sheets, which will decorate the area and provide you with maximum comfort on hot summer days.

A simple, practical shower looks like B-pillar with plumbing and side walls, which are covered with corrugated board.

Stage 1. Digging a pit

A shower in a country house made of corrugated sheets can have different designs and be located above the pit itself or not far from it. If drainage system is installed directly under the shower, then for this purpose a hole is dug at least 50 cm deep and for 40-45 of them it is filled with large crushed stones, stones, brick fragments, etc. Upper layer covered with small crushed stone. This foundation has already been laid wooden grate 10 cm high is the shower floor. You can do it yourself, keeping a gap of 0.5-1 cm.

In the second case, when there is no hole under the floor, you will need to create a drain - for example, by concreting a pipe and a plastic drain into the floor or using a special tray. Discharge must be carried out into a special sump or into a drainage ditch. The first could be a Eurocube, that is, a special plastic container in a metal grid. Two such connected Eurocubes can be a purification facility.

After determining the size of the shower (usually 2x2 or 2x3 m), its base is marked. The earth is removed from this place to the depth of the shovel bayonet. Then the pit is lined with roofing felt and covered with crushed stone in a layer about 15-20 cm thick.

A piece of hose or pipe is placed in the same hole, which is led outside the perimeter of the shower itself. The pipe can be laid on the surface or in a trench. Now a tray with a drain is placed on top, which is connected to the pipe. You can just get by with concrete or tiles.

Stage 2. Install the metal frame

Country shower Corrugated sheeting is made on the basis of a frame made of profile pipes. You need to calculate its dimensions based on what sheets of corrugated sheets you have. The pipes will have to be dug into the ground to a depth of about a meter and this also needs to be taken into account.

Four racks of profile pipe concrete is placed in the corners of the shower, and the fifth is needed to hang the door. Then horizontal jumpers are prepared to connect the racks from below, above and in the middle - it is recommended to use welding, as this is the most reliable method.

If you work with welding machine in this case is impossible, then it is quite possible to use metal screws. You can also take screw connections, but you will have to drill holes for them. The finished frame is coated with an anti-corrosion substance and painted.

Stage 3. Raise and secure the barrel

It is necessary to strengthen the roof, for which profile pipes are also suitable. They will serve as lags, that is, bars on which the roofing material. A container of water is placed on top of this.

Both plastic and metal tank recommended volume from 150 to 200 l. If you are interested in quickly warming up the water, then pay attention to flat designs dark color. It is better to initially take a black tank from an easily heated material, but you can simply paint the barrel black, install it and securely fasten it to the roof.

Stage 4. We cover the shower with corrugated sheets

Using self-tapping screws, the frame is sheathed with corrugated board. At the same time, verticality is constantly checked, for which you will need a level. It makes sense to take a ready-made door, but you can do it yourself if you have time to tinker.

Stage 5. Install the plumbing

The tanks we sell already have holes for both showers and water intake - you just need to connect the supply hose, mount the faucet and install a watering can/sprayer. But for an ordinary barrel you will have to go through the following series of procedures:

drill a hole;
insert a piece of threaded pipe;
install a tap;
put another piece of threaded pipe (squeeze);
connect a sprayer or watering can;
cover the barrel from leaves and debris.

You can watch the construction of a shower from corrugated sheets in the following video:

Many people in summer time prefer to leave stuffy city apartments and spend time in suburban areas. However, the absence of such a benefit of civilization as a shower can significantly spoil the impression of even the most best vacation Outdoors. The solution to this problem is an outdoor shower, the construction of which is the subject of this article.

General information

Building an outdoor shower yourself is not at all difficult, and you don’t even need to spend a lot of time on it.

All you need is:

Prepare a tank of suitable volume;
Make the frame of the future shower stall;
Cover the frame with any sheet material.

The main part of the work is making the frame. If you know how to work with a welding machine, then the best option there will be a frame made of profile pipes. This material is inexpensive, strong and quite durable.

Advice! If it is not possible to make a shower from pipes, you can use it for these purposes wooden beam, pre-treated with an antiseptic.

Below we will look at how to build a summer shower from pipes.

Construction Features

Materials

So, to build a summer shower from a profile pipe, you need to prepare the following materials:

Selecting a location

Before starting construction, you need to decide where the country shower made from a profile pipe will be located.

The following requirements apply to the site for future construction:

It is advisable that the shower be located on a hill, which will improve the flow of water. If there is no such place on the site, you need to dig a drainage hole.
The place should not be shaded, which will allow the water to quickly heat up in the sun.
If there is a well on the site, the distance from it to the future shower should be at least 8 meters. In addition, the shower should be located at a sufficient distance from the foundation of the house.

Project preparation

Any construction, as you know, begins with the preparation of a project, and the construction of a summer shower is no exception. At the design stage, it is necessary to determine the size of the future structure and its design.

Most often, summer showers have the following dimensions:

Height - 2 -2.5 m.
Length and width – 1.5 m.

Of course, you can change the dimensions if you wish. For example, many increase the area of the building and equip it with a locker room. The latter can be separated from the shower with a curtain or partition.

Preparing the base and drainage pit

Do-it-yourself construction should begin with preparation drain hole and grounds. The size of the pit depends on the number of people living. The pit should be located close to the booth itself, for example, behind it.

The bottom of the pit must be filled with sand and gravel, and the walls are lined with stone or brick. When the pit is ready, you need to make a foundation with a drain.

The work is carried out in this order:

First of all, you need to prepare the site - remove debris and grass.
Then it is laid so that it goes into the hole at an angle. It is best to place the drain in the center of the shower stall.
Next, you need to mark the future site and make formwork from boards or other material along the contour.
After this, the bottom of the formwork must be covered with a layer of crushed stone and compacted.
Then supports are installed at the corners of the formwork. To do this, the pipes need to be driven 20-30 centimeters into the ground. The racks can be positioned vertically or at a certain angle, as shown in the diagram.
After installing the racks, a metal reinforcing mesh should be laid, which should rise slightly above the surface of the crushed stone.
To complete the work, you need to fill the formwork with concrete.

Frame making

When the concrete hardens, you can make a frame for a summer shower from a profile pipe. Since in the process of work concrete screed will not be subjected to heavy loads, it is not necessary to wait 28 days for the concrete to gain grade strength.

The manufacture of the frame begins with the construction of a frame for the tank. To do this, you need to connect the racks along the perimeter, as well as diagonally. Then the racks must be connected with cross members located on three sides, which will add rigidity to the structure.

At this point, the frame for the shower from the profile pipe is ready, now you can start arranging it and covering it.

Shower arrangement

The arrangement of the shower begins with the installation of the tank. It is desirable that the container be flat and wide. In specialized stores you can purchase a special tank for a summer shower with installed fittings.

If the container has enough surface area, it can serve as a cabin roof.

Otherwise, you will first need to lay the roofing material.

A fitting should be cut into one of the walls of the tank, which will face the cabin.
After installing the tank on the roof, it is attached to the fitting ball valve and a shower head. The water supply is regulated by a ball valve.

Advice! To make the water heat up faster, the tank should be painted black.

Owners summer cottages They are trying to supply water to the house and provide basic amenities. You can build a summer shower at your dacha with your own hands, either temporary or permanent - the type of future structure is selected depending on individual needs.

Before you build a shower in your dacha with your own hands, you need to competently carry out the design, determine the location of the future structure, and select materials. The room should be uncrowded, as comfortable and convenient for use as possible.

Selecting a location

In order to ensure rapid drainage of water, it is optimal to install the shower on a flat or slightly elevated area. You should not choose a site located in a deep depression or in a hole.

To avoid water stagnation, choose the right place to build a summer shower

The optimal location for a country shower would be an open area, well lit by the sun, located at some distance from other buildings. In this case, the barrel will naturally heat up under the sun, providing warm water. This condition can be neglected only if it is planned to build a shower stall with heated water.

At the same time, the site where construction will be carried out should not be too far from the house - after water procedures, it is advisable to get from the shower to a warm room as quickly as possible.

Size calculation

When building a country shower, the following parameters are used as standard:

height - 200–300 cm;
length - 190 cm;
width - 140 cm.

An example of drawing up a drawing of a summer shower

The indicated dimensions are very convenient because, taking into account the thickness of the walls, the building will ultimately have an area of 200x150 cm - this is a completely waste-free option when using boards standard sizes. As a result, 100x100 cm will be allocated for the shower stall, and 600x400 cm for the changing room.

Required tools and materials

You will need the following tools:

roulette;
corner;
level;
hammer.

In addition, you need to stock up on nails and a ball of twine. Separately, you need to purchase a tank, as well as pipes, a couple of taps and a shower divider. Brick, iron or plastic sheets are suitable as building materials for the construction of the cabin, wooden boards, for the construction of the frame - pipes.

Tools needed to build a shower in your country house

For the foundation pouring and construction of brickwork, a certain amount of cement, sand and concrete will be required, and for the final finishing - insulation materials, paint, plaster, hooks for clothes, shelves for bathroom accessories and other accessories.

Options for shower designs for a summer residence

The simplest option for a summer residence is a compact portable shower, which is suitable for one-time water treatments, has a standard volume of 20 liters and is designed to supply water for 10 minutes. The operating principle boils down to filling the reservoir with water and then heating it in the sun, after which the portable shower is mounted to a height of 2 meters and is ready for use.

Portable shower

An open shower also has a simple design, the installation process of which boils down to the following steps:

attaching a branch water pipe to the wall;
connecting a pipe and a watering can using a hose;
fixing the watering can holder;
installing a screen.

A common option for summer cottage is the so-called change house with a shower, the design of which assumes the presence of a solid modular container or a frame-collapsible block.

Options for a stationary summer shower for a summer residence

Installation of this structure is quite simple - the territory is marked, the top ball of soil is removed and leveled, a cushion of sand and gravel is created, on top of which boards are laid. A block assembled on site or a ready-made structure is installed on the soil prepared in this way.

Of course, the most durable shower will be a stationary shower, but its construction will require more effort and time.

Preparing the base

It is much easier to erect a frame structure than a permanent structure - depending on the type of structure chosen, the stages of preparing the site for construction will differ.

For a temporary structure, it is enough to simply remove 10-15 cm of the top layer of soil from the site to level it, and then fill it with sand.

For a country shower, you will need to lay a foundation, the depth of which is determined by the materials used for its construction. For example, for a brick shower, a foundation with a depth of up to 30 cm will be sufficient.

Foundation for the construction of a capital summer shower

The foundation is laid in the following sequence:

pegs are driven into the outer corners of the future shower;
a cord is stretched around the perimeter;
a place for pipes is prepared (a log or branch wrapped in roofing material is laid);
concrete solution is poured.

Advice! The formwork equipment will allow you to extend the period of operation of the shower - it is recommended to increase the level of the entire foundation by 10 cm, raising it above the ground using boards reinforced with stakes and spacers.

Drain pit equipment

The pit volume is usually more than 2 cubic meters. m, while its walls must be strengthened in order to avoid possible scree. The drain is located a few meters from the shower, but not under the building itself or near its walls - this will lead to the destruction of the foundation in the future, as well as the appearance of unwanted odors.

Example of equipment for a drainage pit for a summer shower

The drain must be laid with a waterproof layer - roofing felt, hydroglass insulation, PVC film or concrete screed (reinforced with metal mesh) is used.

Attention! A common mistake is to use clay as an insulating material, which erodes and soon clogs the drainage ditch.

Installation of a frame for a temporary shower stall

If for a capital structure it is fulfilled brickwork, then for a temporary one a frame is usually installed: metal or wood. In the latter case, the wood should be treated with special impregnations that will protect it from insects and moisture, preventing the formation of fungus and mold.

Wooden frame for summer shower

Markings are made - a rectangle is marked directly on the ground, the sides of which correspond to the dimensions of the future country shower.
Wooden beams are installed, the width of which reaches up to 10 cm.
Bandaging is carried out - starting from the top, the structure is securely fastened with bolts, after which the beams that form the basis of the shower walls are connected.
Walls are installed, for the construction of which you can use either boards, slate or plastic panels.
The pipes are being laid out - the water supply is installed so that the pipe outlet under the shower hose is higher than the level of the head (this will provide the necessary pressure for water movement). The drainage is discharged into a sump tank or into a specially equipped septic tank.
The tank is installed - a threaded outlet is made, a tap with the appropriate nozzle is installed, after which the barrel is lifted up and secured.

Suitable as a tank for a country shower plastic container, which can be purchased at a specialty store, or another barrel available on the farm. It is desirable that it be flat and proportionate to the area of the building so that the weight is evenly distributed over load-bearing structure. Its volume is selected at the rate of 40 liters per family member, but the barrel should not be too heavy - its maximum volume is no more than 200 liters!

Solar water heating tank

Advice! So that the owner of the dacha does not have to carry water to the tank himself every time, it is possible to equip it with automatic filling.

Lighting and ventilation of a country shower

When doing the wiring yourself, it is important to follow all electrical installation rules and adhere to safety precautions. Separately due to high humidity Care should be taken to insulate the wiring.

Window for summer shower ventilation

Interior shower decoration should be made of moisture-resistant materials: plastic panels, pieces of linoleum, oilcloth, etc. If wood is used, then each individual board is covered with hot drying oil.

The concrete floor is usually covered with gratings made of plastic or wood, and rubber mats are laid on top. It is quite convenient to equip a small changing room directly in the shower. To prevent water from getting into it, the floors in it are slightly raised by a couple of centimeters - this can be easily achieved by additionally installing a tray.

Internal structure of a summer shower

Concerning exterior finishing, then similar materials that have already been used for decoration will look harmonious country house and other buildings on the site.

To use the shower not only in summer, but also in colder seasons, it is recommended to insulate it with polystyrene foam, which is placed in the interior space and covered with PVC film on top. The walls are usually painted or plastered, covered with clapboard or siding.

How to build a summer shower in the country: video

Types of summer shower: photo

If you spend the warm season at your dacha or on a country plot, then before the start of the season you should spend some time and build a wooden summer shower with your own hands. Even if you have a shower in your house, such a structure will definitely not be superfluous: in the summer heat, dousing yourself with cool water, slightly heated under the sun, is really very pleasant.

Moreover, such a structure is quite simple to install, so even not the most experienced craftsman can cope with the task.

Tools and materials

Before we start work, we need to stock up on everything we need.

Wooden beams with a cross section of 50x50 mm and a length of up to 2.5 m. We will need from 4 to 6 such parts for the manufacture of vertical supports.
Beams or thick boards for the top and bottom trim, as well as to strengthen the frame.
Wooden slats for flooring.
Lining for covering the walls of a shower stall.

Advice!
The best option would be to purchase larch blanks.
Maple, pine and ash also tolerate loads well, but cope less well with moisture.
In principle, oak can also be used, but for this purpose it is too expensive.

Water tank on the roof. It is advisable to purchase a special container with a wide neck and a lower pipe to which a faucet and shower head are connected.
If necessary, a shower tray (you can do without it).
Various accessories - towel racks, shelves, curtains, etc.

In addition, we will need consumables:

Fasteners - screws or nails.
Concrete for installing supports in the ground.
Materials for arrangement drainage well or .
A product for impregnating wood and protecting it from moisture and microorganisms.

As for the tools, here you can get by with a standard set:

Entrenching tool for excavation work.
Devices for mixing concrete (mixer or regular trough)
Wood saw (circular, reciprocating or hacksaw).
Drill or screwdriver.
Building level.
Hand tool.
Brush or spray for applying moisture-proof impregnation.

When everything is ready, you can start working.

Drainage options

Drain pit

Before you start building a shower, you need to understand where all the waste water will go. The easiest way is to drain it onto the ground, but this is only possible if the shower is located at a distance from the site, and even on well-drained soil. Otherwise, we cannot avoid contaminated water getting into the beds or water intake sources.

Most often, a separate drainage well is installed for the shower:

In the selected area, we dig a hole up to one and a half meters deep.
We protect the walls of the pit from getting wet and collapsing by installing wooden formwork, masonry from ceramic bricks or old car tires.

Advice!
Price quality bricks is very high, therefore, for the construction of drainage pits, they most often use broken stones, or they take stones that have been used, but still retain their shape.

We lay drainage material at the bottom of the well. For this purpose, either pebbles or large crushed stone are used.
We make sides on top on which the frame of the shower stall will rest.

Septic tank or cesspool

If there is a cesspool or a septic tank, and we plan to install a shower no further than 10 meters from these structures, you can simply arrange a drainage ditch:

In the place where the shower is installed, we dig a shallow (up to 30 cm) pit. It will contain .
From the pit to the septic tank we dig a trench up to 20 cm wide. The optimal slope towards the drain tank is about 3 - 5 cm per 1 m.
Next, you can proceed in two ways: either concrete the bottom of the trench and cover it from above, leaving several inspection gratings, or lay sewer pipe for outdoor use. The second option is more preferable, and in terms of costs it will be approximately equivalent to the first.

At the same time, everything wastewater, formed under the shower, will be transported as quickly as possible to the septic tank, where they will be included in the process of waste decomposition and infiltration of purified liquid into the ground.

Important! If the design of your septic tank provides for regular pumping, then with the addition of a shower, the amount of drainage will approximately double. This fact should be taken into account when planning preventive measures.

Building a shower

Frame and sheathing

If we take the drawings of a wooden summer shower given in the article as a basis, anyone can build such a structure with their own hands.

However, beginners should carefully study the algorithm of work in order to avoid annoying mistakes.

The shower stall usually has small area at considerable altitude. This makes the structure unstable, which is why it is most often installed on supports buried in the ground.

Note!
This does not apply to lightweight portable showers with slatted frames - they are usually simply tied with wire to reinforcing bars driven into the ground.

To install supports, we make nests up to half a meter deep in the soil.. We fill the bottom of each nest with gravel - it will prevent the stand from sagging under its own weight.
We impregnate the lower parts of the racks with an antiseptic, wrap them in roofing felt and concrete them in the ground.. After pouring the concrete, we adjust the position of the supports according to the level and fix them in a strictly vertical position.
After this, you need to give the concrete time to gain strength.. Since the load on the supports will not be very large, the required 28 days are rarely waited: even a week is enough.

At the bottom we attach a harness made of beams. We install on them either a pre-purchased shower tray or a grid of slats connected to gaps of 0.5 - 1 cm for water to flow out.

Advice!
The grate must be thoroughly sanded, otherwise the risk of getting a splinter in your bare foot will become very noticeable.

We install cross members in the middle part and reinforce them with braces. We connect all the parts using nails or self-tapping screws, after impregnating them with a moisture-proof compound.
We make the upper harness from the beams. We also install transverse joists that will hold the water tank.

We cover the outside of the shower stall with boards (lining is best). Most often, the sheathing is not brought to the floor by about 25 - 35 cm - this ensures optimal air circulation.
We install at the front wooden door with external and internal latches. Instead of a door, sometimes they simply hang a plastic curtain: this design is easier to manufacture, but less convenient to use.

Advice!
It is worth attaching several hooks to the outer wall next to the door.
We will hang clothes and towels on them: this way they will not get wet during water procedures.

Equipment and decor

All we have to do is equip the water supply system.

And here it is best to implement classic solutions:

On top part In the shower we install a water tank. An industrial container made of dark plastic, with a neck located on top and a nozzle for a shower head on the bottom, is ideal.

Note!
Instead of a factory container, it is quite possible to use metal barrels, and polymer containers.
The main thing is that the structure is sealed and does not release toxic substances upon contact with water.

In areas where the only source of water is a well without a pump, the tank must be filled manually using buckets. To do this, we attach a fairly strong ladder behind or to the side.
If there is a water supply on the site (no matter whether it is central or autonomous), then it is much easier to connect a hose to the container on the roof. By connecting it to the water supply, we can quickly and effortlessly fill the tank with the amount of water we need.
In summer, the water in the tank heats up quickly. But in spring and autumn, taking a cold shower is not very pleasant. To ensure more efficient heating, we build a slatted frame around the tank, which we tighten transparent film or glass. Such an improvised greenhouse will provide comfortable temperature water even on a cloudy day.
We attach a watering can with a tap inside the cabin, checking the tightness of the pipe.
On one of the walls we attach a shelf for soap and a hook for a washcloth.

After this you can use the shower. And so that it lasts as long as possible, before the start of each summer season the cabin should be sanded and treated with an antiseptic, and then either coated with varnish for exterior use or applied wood paint.

Conclusion

A summer shower made of wood, made according to the above algorithm, is quite simple, reliable and convenient. However, you can always make adjustments to the design, introducing either your own ideas or technical solutions, gleaned from the educational video in this article.