Do-it-yourself winch - simple manufacturing methods. Manual hoist - how to feel like a titanium? Do-it-yourself chain talc

Homemade winch (telpher, hoist). How to do lifting mechanism for garage, workshop, construction site.
Many home craftsmen would like to have some kind of lifting mechanism, such as a hoist, hoist or winch, in their garage or workshop. Of course, you can buy them ready-made, but they are usually not very cheap - several thousand rubles. And they are not often on sale. Automotive rescue lever winches available in almost any store cannot be used for lifting loads. Because their stoppers are made using a ratcheting mechanism. But it only works well in one direction. It is easy to lift a load with such a winch. But lowering it smoothly is problematic. When independently manufacturing hoists or winches, the master is faced with the problem of where to get a powerful, reliable gearbox (with a gear ratio of at least 1:20 - 50) and always with a self-braking effect. As a rule, these are powerful worm gearboxes and they don’t often fall into the hands of a master.

Meanwhile, almost anyone can make a homemade winch or hoist, and, as they say, from scrap materials. Threaded rods up to 2 meters long are available for sale. And it can serve as an excellent gearbox for a homemade lifting mechanism.

The design of such a winch is clear from the sketches. The principle of operation of the winch is simple. If you rotate the threaded rod itself, and the nut on this stud is not allowed to rotate, then the nut will move along the stud. The force during this movement is much greater than that required to rotate the pin (all screw jacks work on the same principle, the increase in force there reaches 20-30 times the magnitude).

The ends of the stud are fixed in bearings, which in turn are installed in supports. A stud nut is a rectangular metal plate to which regular nuts are welded. The plate prevents the nuts from turning. A cable is also attached to the plate. The cable is passed through one of the supports and thrown over the block. At the other end of the cable is a lifting hook or sling system (this depends on the purpose of the lifting winch).

The pin drive is easiest done manually. To do this, a pulley or gear is attached to one of its ends. (you can, for example, even use a bicycle). A strong cord or chain is thrown through a pulley or gear in an endless loop. If you pull on one side or the other of the cord, the pin will rotate and the nut will move along the pin. Accordingly, there will be a cable behind you, and the load will either fall or rise. The self-braking of the mechanism is absolute; no force on the nut will force the pin to rotate. Most likely, the whole thread will break off.

Of course, you can also make an electric drive using any reversible electric motor with a power of 200-500 W. It is convenient to use, for example, some inexpensive electric drill with a rotation direction switch. Nowadays there are many such drills available for sale. The electric drive can be made either directly or through an additional pulley or flexible shaft.

Such a homemade winch can lift a weight of several hundred kilograms. In most cases this is sufficient for household needs. The length of the stud, or rather the ability to move the nut along it, determines the lifting height (in the simplest version of this homemade hoist). If you take a 2-meter long hairpin, then this height will be approximately 170-180 cm, which in the vast majority of cases is more than enough for a home workshop or garage. However, it is not difficult to increase the lifting height using simple techniques.

The support (base) for such a winch can be made from durable dry wooden beam or thick board. Although of course it is better to use metallic profile or channel. All connections are made by checking or using bolts. It all depends on the purpose and capabilities of the master. It is not difficult to organize the movement of this hoist under the ceiling. For example, with the help of some T-beam, located in the center of the workshop. And install the caliper itself on the beam so that it can rotate around its center. Then almost any point in the garage or workshop will be accessible. A similar result can, of course, be achieved with the help of various blocks, it would be possible to attach it to something. Of course, the floor beams of the building must also be designed for additional load.

Based on such homemade winches, you can make a homemade crane. This will require at least two of these winches. It is most convenient to place them in the crane boom. One of the winches will lift the boom itself (change its angle of inclination), and the second will lift the load itself. Of course, you shouldn’t forget about the counterweight.

The simplicity and accessibility of such a homemade winch opens up quite a wide scope for its use in a home workshop, garage or construction site.

Konstantin Timoshenko

A hoist is a device for lifting and lowering a load. In addition, such a mechanism can hold the load in a suspended position. Hoists can be manually or electrically driven. With an electric drive, an electric motor is responsible for the movement of the cables. The manual hoist uses a chain mechanism. Such a device can be gear or lever. In this article I will talk about the principles of operation of a manual hoist.

Most a good decision To lift the load and work with it at height, a manual gear hoist is used. This mechanism is designed for raising and lowering loads of various configurations. As the name of this device implies, the mechanism is driven manually. This does not require an energy source. A person who does not have much strength can operate a manual chain hoist.

The operating principle of a chain hoist is not very complicated. This mechanism can be used as a stand-alone lift or as part of a crane beam structure. The hoist can be mobile, lever or stationary.

To work with a stationary hoist, the operator must be located directly next to the load. Thanks to the rotating casing, the load can not only be raised and lowered, but also unfolded for more comfortable work with him.

The mobile chain hoist is attached to an I-beam profile, along which, using the carriage included in the hoist, loads can be moved in two directions: vertical and horizontal. Such a hoist, which is mounted on a carriage, is called a telpher.

How does a chain hoist work?
A chain hoist consists of two blocks and a chain thrown between them. The lower block has chain sprocket, and on the upper block there are two stars of different diameters. It is because of the difference in the diameters of the sprockets that the load is lifted more efficiently.

In addition, we should not forget about increasing the efficiency of the hoist due to the block system.

Advantage of chain hoist:
Compactness;
Light weight;
Ease of use;
No energy consumption;
Durability;
Relatively low cost.

You can learn about chain hoists on the website stropu71.ru.

Here you can also purchase cable slings and others lifting mechanisms and accessories for them. The Partner StroyServis company has been supplying lifting and geodetic equipment for about ten years. In addition, the services of this company include the design and manufacture of slings and ropes of any size and type.

The movement mechanisms of hoists, the load capacity of which is 1, 2 and 3 tons, include such elements as a driven and idle trolley, and a traverse. Using the last element, the lifting mechanism is fixed and connected to the movement unit.

The hoist trolleys are attached to the traverse using hinge pins vertical type. This design ensures a turning angle of the trolley of 15-18 degrees.

Thanks to the hinged design (on vertical axes guide rollers are provided) the hoist with the movement mechanism passes freely along paths that have a minimum radius of curvature.

Due to the low-mounted electric motor, the movement mechanism of the electric hoist easily overcomes small switches.

The monorail mechanism for moving electric hoists is offered in normal and reduced dimensions.

The movement mechanisms of normal-sized hoists are equipped with one common sidewall on each side. The motor is mounted on one side via a flange. The connection between the motor shaft and the primary gear is realized through the use of a reduction attachment.

A hoist with a movement mechanism of reduced size is characterized by a different type of design. Instead of two, there are 4 sidewalls (two driven and two driven).

On devices with low load capacity and low lifting height, only 1 trolley is provided. The trolley is rigidly fixed to the body using a frame.

For hoists equipped with a pair of trolleys, 2 types of fastening are provided - rigid (frame) and hinged (special bolt).

Variations of fastening mechanisms for moving electric hoists

The design of the lifting mechanism is adapted to fix the unit for moving the load along a horizontal plane. Such mechanisms are being developed for monorail or double-rail tracks. Clamps can be of the following types:

Rigid (hinged) – for a normal-sized movement mechanism. Pulley hoist 2/1 and 4/1. Figure 4A shows an electric hoist with one trolley.

Hinged (Fig. 4B I) – lifting device not rigidly fixed around the axle and road wheels.

Swinging or semi-hinged - the lifting mechanism swings. In Fig. 4B shows an electric hoist with two trolleys.

Non-jointed 2/1 and 4/1. Designed for hoists with reduced dimensions of the movement mechanism. The lifting unit is mounted on the side of the rail track. This design allows you to save useful space.

Lifting mechanism with a unit for moving along a double-rail track. Fig 6.

Figure 4 shows a diagram of the movement mechanism, which includes an electric motor (2), a gearbox (3), a driving unit (4), and a driven unit (5).

A homemade manual hoist is a good replacement for industrial designs, because it is no less effective. So it’s worth getting such a helper in your household, and we will help you do it and tell you about this device.

How does a manually driven hoist work?

A hoist is a suspended lifting device. It can be manual or with electric drive, the second option is, of course, more common. A hoist, in general, is a special mechanism for lifting or lowering various loads, as well as for moving them. The lifting capacity can be up to 10 tons, and objects can be lifted to a height of up to 12 m - you must admit, not bad for a manually driven mechanism.

Based on these indicators, use this device possible for moving various goods of large weight, these can be objects household appliances – gas stoves or refrigerators, freezers or washing machines etc. Trade workers often use them to put goods on shelves. You can’t do without manual hoists during construction or repair work ah, where you often have to raise Construction Materials or tools.

An ordinary manual chain hoist has the following main elements: a chain hoist, consisting of movable and fixed blocks connected to each other; two-stage cylindrical coaxial gearbox, which has a manual mechanical drive; output shaft; specialized disc brake; additional load braking system; block pendant with hook. The operating principle is based on traction and load chain systems that have round links. The main types of manual hoists: gear and lever.

Gear manual hoists – is their popularity justified?

The main advantage of this type of hoists is considered to be simplicity of design and reliability. You can’t do without them in many industries: neither in the construction, nor in the mining industry, nor in agriculture, nor at fuel and energy enterprises and others. This device can be used not only indoors, but also outdoors. outdoors, even if there are no power sources. Moreover, such hoists are not only safe to use, but also unpretentious to use and have a durable mechanism.

The gear type of hoists is suitable for working with large loads weighing from 0.5 to 10 tons, and they can be freely lifted to a height of up to 12 m. A special load chain with a hook is designed for such a load, and the available additional drive chain will ensure not only good movement, but also easy movement of loads. You need to control the operation of such a hoist while standing on the ground. The action begins with the drive chain, this device is a stationary mechanism, and its purpose is to raise or lower loads from high shelves.

Monorails are installed indoors to move goods using hoists. Such stationary devices are usually used when there is no need to constantly move and lift loads. They are not designed for a large amount of work, and the movement speed is very low, this must be taken into account when choosing of this instrument. But at the same time, if you need to lift a fragile product or object, then these are the most successful hoists. Now we need to talk about the competitive model.

Lever hoist – advantageous physics of load capacity

This type of hoist is necessary for working with small loads, the weight of which is no more than 5 tons, and it can be raised to a height equal to the height of a person. It all depends on constructive solution. Raising, lowering and moving is carried out using a lever built into the body. The hoist is controlled by an operator located near the device. Such models are good for tensioning cables and lifting loads. Since they are not suitable for a large volume of work, utility services find use for them.

They are necessary when you need to tension cables or install pipes at the bottom of trenches, as well as for installing hatches. With their help, foresters pull out stumps, and industrialists place heavy equipment in workshops. Often their purpose is to lift a load in order to work with it, like this. This can be various repair work, for example, in car repair shops. To make working with lever hoists easier, they are additionally equipped with special trolleys.

Worm worm hoists - a compact strongman

In addition to these main types of manual hoists, there are also others. Lately, worm gear hoists are often used. To operate, they are hung stationary or a mobile “cat” is used. This is convenient for moving loads horizontally; such hoists can move along I-beams. There are a lot of models of this type of device. They are used for lifting or holding loads in a raised position; they are also suitable for moving. Everything happens along a special suspended track made of I-beam profile.

Their advantage is that work can be performed in small spaces, and the distance between beams and loads can be insignificant. Such hoists can also be used for work outdoors.

They have some features, for example, a rotating casing (and the design can rotate all 360 degrees) allows you to control work from anywhere, that is, you can raise and lower the load in any position. This creates additional security, the operator during operation can be located on the side of the hoists and also from the load itself. Also this type The hoists are distinguished by their reliability, wear resistance and low-heating brake. All this makes them quiet and comfortable. And thanks to the low building height, you can work with this equipment in confined spaces in vertical positions.

Homemade manual hoist - a free household assistant

Often you have to carry out repair work at home, and you need to lift tools and materials. If you buy a manual hoist, it is expensive, and often you don’t have time. In this case, you can do it yourself.

A movable and simpler stationary crane beam in the garage with your own hands is quite doable if you have a welding machine and two days of free time. For a professional auto repair shop, it is easier to buy ready-made lifting equipment.

If the need for a crane is rare, then it is cheaper to make a simple and reliable lift yourself. Such a homemade crane can easily lift a weight of up to 800 kg, and this is quite enough for repair work in the garage.

In order to make a frame for a small beam crane in a standard garage with your own hands, you will need the following materials:

I-beam (4 - 4.5 meters) - the required footage depends on the height of the garage;
pipe (diameter 10-12 cm), length 2.4 meters - 2 pieces;
one square pipe (10x10 cm);
corners (10x10);
manual hoist and hoist;
bolts (M16) with nuts.

If you plan to build a mobile crane beam, then you need four more rollers and a hoist.

The procedure for making a crane frame with your own hands:

We weld the legs of the crane - you need to weld the corners on both sides to the I-beam pipe;
The location of the corner is at an angle of 45 degrees. The result is a kind of stiffening ribs that will firmly fix the stand, which bears the bulk of the weight of the load carried by the crane;
We weld two triangles and spacers on each crane post.

if the crane is a mobile beam, then on both sides from the bottom, on each stand, a roller must be welded horizontally - ordinary rollers for metal containers will do, furniture rollers will not withstand the weight;
At the top, we fix a pipe as a crossbar along which the lifting mechanism will move;
We weld an I-beam in the center of the pipe to secure the roller along which the steel cable of the crane’s lifting mechanism will move.

above I-beam We weld a piece of a square pipe (to give rigidity to the frame) - 40 cm. The pipe should protrude on both sides by at least 20 cm. It turns out that the side post is located in the middle of the crossbar stiffening pipe;
V square pipe insert the transverse pipe of the frame crossbar;
We drill through holes for fastening bolts on both sides of the square holder and in the crossbar pipe itself - we need rigid, reliable fixation on both sides of the vertical post.

The result is a U-shaped structure of the crane frame, which is installed on rigid legs with spacers, and a crossbar pipe is rigidly bolted to the top.

Installation of lifting mechanism - manual or automatic

To mechanically lift loads onto the frame, you need to install a manual hoist - a worm winch and a cable. How to attach the hoist to the frame:

on the side of the rack we install a manual worm winch (load capacity 800 kg, no less);
The steel cable moves along rollers.

This mechanism makes it easy to lift the engine or a car behind the hood on one side.

You can use the lifting mechanism and rollers from the elevator door as a drive. The rollers there are reliable and durable.

An electric lift drive can also be installed on the manufactured base. A 300 - 500 W motor will be quite enough for simple repair work in the garage.

Such cranes are often used for the repair and reconstruction of old wooden houses. Construction log house it will go faster if the logs are laid using a mobile homemade crane. In this case, the width of the frame is the length of the logs.

You can also make a simpler lift for the engine, on one support, watch the video.

The winch is one of the oldest devices that facilitates the movement of heavy objects, invented by man much earlier than he knew the laws of physics. The principle of operation of the winch is based on the rule of leverage: by applying minor forces to the handle, you can move and lift quite heavy objects. Winches and hoists are widely used on the farm for lifting building materials, dragging loads, and even for plowing land. Winches, powered by manual or electric drive, are also indispensable for lovers of off-road travel.

Buy a winch or make it yourself? Which winch design is better? The answers to these questions depend on how often you plan to use it and what loads you move. Manual winches require force but are not dependent on electrical power. An electric winch can move heavy loads without any effort on your part, but it must be powered or battery-powered. Below are the designs of several winches that you can make with your own hands; which winch to choose is up to you.

Winch made from a cable and a piece of pipe

Option simplest winch, which can be literally made from scrap materials and in a few minutes, is popular among car enthusiasts. This design is a cable rigidly attached to a piece of pipe placed on an axle. The axle is driven into the ground or secured in some other way. Any lever is slipped under the bottom turn of the cable: a shovel handle, a pipe, a strong pole. By rotating the lever so that the cable is wound around the pipe, you can move a fairly heavy object, for example, a stuck car. This device cannot be called a full-fledged winch, but it performs its functions.

Manual winches include any devices that allow you to move loads and are manually driven. The most common are drum-type winches: a cable is wound on a reel, and the rotation of the reel is carried out using a handle through a gear transmission: a worm or a sprocket system different sizes. The higher the gear ratio, the less force is required to apply to the handle.

For efficient operation The hand winch must be rigidly fixed to a stationary object; for this purpose, mounting holes are made on the winch frame. The handle is connected to a shaft on which a small sprocket is rigidly fixed. The coil is rigidly connected to a large sprocket, which has a clutch with a small one. The cable is attached at one end to the reel, and a carabiner or hook is attached to the other end.

Do-it-yourself winch with manual or electric drive

If you have the skills to work with a welding machine, you can make a winch yourself from scrap materials.

You will need:

Pipe rectangular section for making a frame;
Pipe or finished drum shaft;
Sheet metal for drum discs, thickness 3 mm;
Threaded rods M10-M12, 24 cm long – 6 pieces, nuts;
Tube with a diameter of Ø14 – 6 identical pieces of 20 cm;
Large and small sprockets and chain;
Hubs for attaching the drum to the shaft and for attaching the shaft to the frame;
Lever for manual drive, gasoline or electric motor, powered by ~220 V mains or car battery;
Cable required length with a carabiner at the end;
Welding machine and electrodes;
Grinder with cutting and grinding disc;
Paint and primer for metal;

Set of wrenches.

Winch manufacturing technology:

According to the drawing, a 20x20 mm rectangular pipe for the frame is cut with a grinder. All connections made perpendicularly are obtained by cutting the workpieces at an angle of 45 degrees.
Lay out the workpieces on a flat surface. Weld the winch frame using welding machine pointwise at the junction of the workpieces. Check the perpendicularity of the corners and the consistency of the dimensions, after which the seams are completely welded. Weld the platform from sheet metal with longitudinal grooves for mounting the drive motor. Remove scale and burrs with an angle grinder grinding wheel.
Sand the frame, cover it with a metal primer, and after drying, paint or enamel in two layers.
Start making the drum. Two circles of the same diameter are cut out of sheet metal - approximately 30 cm. A hole is drilled in the center of each circle according to the diameter of the shaft, and six holes are also made at a distance of 7-8 cm from the center. Drill holes for fastening the hubs - 4 on each disk. Attach the hubs to bolted connection. The drum disks are fastened with studs: each stud is secured in one disk, a Ø14 tube is put on it, after which a second disk is put on the studs and tightened onto the nuts and locknuts.
The drum is mounted on a shaft. The shaft can be made from metal pipe suitable diameter or use a ready-made shaft made of high-strength steel from any mechanism. On the shaft with outside a large sprocket is attached to the drum - you can use a sprocket from a motorcycle gearbox, for example. Hubs are installed on the protruding parts of the shaft to secure the drum to the frame.
Install the drum with the shaft on the frame, securing them with external hubs and bolts. An electric or gasoline engine with a small sprocket rigidly fixed to the output shaft is installed on the platform. Put on the chain and adjust its tension by moving the electric motor along the platform in the rectangular mounting grooves to the optimal position. The chain should not sag, but too much tension is not advisable - wear on the sprockets will increase, and the chain may also break. You can check the chain tension by rotating the drum with your hands - it should not hinder the rotation of the drum when unwinding the cable.
Wind the cable around the drum, securing its end to the shaft. The second end of the cable is equipped with a durable carabiner. For ease of movement, the winch is mounted on a frame with a wheel pair using a shank.
Shank with opposite side Designed for attaching a winch to a vehicle. In this case, it is recommended to cover the drum with a protective casing to prevent dirt and precipitation from getting on the cable.
If the drive is planned to be universal, then a handle can be mounted on the outside of the shaft. In this case, in the absence of fuel or electricity, it will be possible to use the winch manually.

The presented winch design is simple and reliable, and although it does not have the ability to switch gear ratios, reverse and other auxiliary functions, it performs the task of moving heavy loads in a horizontal plane perfectly. If it is necessary to lift a load to a greater height, such a winch can be used in combination with a manual hoist or simply by throwing the cable over a strong support.

Thus, in today's lesson we looked at creating a manual winch with your own hands, subscribe to our group and stay updated on all the important news!