How to restore an interior door with your own hands. We restore an old door with our own hands. The main stage of restoration work

Very often, restoring wooden doors with your own hands is the only way out and allows you to keep the door in its original condition without significant investment.

Of course, it will be much easier to get rid of old wooden doors and buy new ones, but there are cases when this item fits harmoniously into the surrounding interior, and it is simply not possible to find a similar one.

It is the restoration of doors with your own hands that allows you to special effort give a second life to an old door.

In this case, the operating principle is the same for both the entrance and interior doors. The only difference may be the presence of a glass insert, which is recommended to be removed before starting work.

It should be noted that you can restore both a door made of veneer and solid wood, as well as an entrance door made of metal.

Preparatory stage of work

Almost any opening made of wood is covered with a special coating in the form of paint or varnish to protect the canvas.

At the initial stage of restoration work, the old coating will need to be completely removed, but before this it is recommended to carefully inspect the door and assess the scope of work.

You can remove the old coating either using a grinding machine or using a fan heater, in some cases remove old varnish Or you can use a special paint remover with your own hands.

If a wash was chosen to remove the top layer, you must carefully read the attached instructions.

As a rule, it is applied to the canvas for some time, after which it is removed using a scraper.

If necessary, to completely remove the old top layer, the procedure will need to be repeated with your own hands.

Old application can also be quickly removed using a DIY fan heater. If you use this universal device, then there will be much less waste from work than when using a solvent.

Such a fan should be directed at the canvas until the coating begins to swell, then upper layer removed with a scraper or spatula.

Caution should be exercised as high heat may damage the product. In the event that door leaf There will be paint left in places; it can be removed from the array using sandpaper.

When using a sander, remember that it only removes the top layer on large cavities. IN hard to reach places you will still have to work manually.

Canvas restoration

At the next stage of work on restoring the old door, it is necessary to restore the door leaf itself with your own hands. As a rule, the most weak point the wooden door is hers Bottom part.

In addition, all chips and cracks can be effectively removed using a special do-it-yourself wood putty. In the case where the lower part cannot be repaired or restored, it can be replaced with a new one.

After the restoration work at this stage is completed, you can begin sanding the door leaf with your own hands.

The work process of polishing a door leaf is conventionally divided into two stages. At the first stage, a rough cleaning of the array is carried out, during which all gross defects and flaws are removed from the old product.

It is best to process the entire surface by hand, and for ease of work, put sandpaper on a block, while hand movements should be directed along the fiber.

Remove all dust from the door leaf with your own hands using a damp sponge.

Painting stage of work

On final stage work on the restoration of the door is carried out by painting it. This can be done either manually or using a spray gun in automatic mode.

When choosing paint and varnish material You should pay attention to the subsequent operating conditions of the product, as well as the type of wood.

If painting will be carried out with a spray gun, the work must be carried out in a well-ventilated area.

In this case, the paint is applied evenly to the entire door leaf in a thin layer, but care should be taken to ensure that there are no smudges left on metal or wooden entrance doors.

The most commonly used method is the manual method of painting the door leaf. This type of painting requires a roller and a brush.

First, the entire door leaf is covered with a layer of primer, after which it must be allowed to dry thoroughly.

When painting the door, it is recommended to install it in a horizontal position, which will significantly reduce the risk of smudges.

At the first stage, hard-to-reach places and all protruding elements are covered with paint, and only after that large surfaces are painted with a roller.

After the restoration of the door is completed, it must be thoroughly dried and hung in place.

Features of restoration of interior doors

At its core, the restoration of interior doors made of veneer has some significant differences.

This work of restoration of the canvas should be carried out with special care and as carefully as possible.

They paint a veneer door in exactly the same way as one made from solid wood. You can use both brushes and a roller, and a spray gun.

An effective way to restore an old interior door, which will make it even more attractive, is to cover it with new veneer.

This wood-structured material itself has an adhesive base. Its texture is completely similar to natural wood and will help to effectively restore even the most unsightly canvas.

Invalid Displayed Gallery

On appearance a door restored using veneer will be no different from one made from solid wood.

You can apply an interesting design, change the facade, or make a stylish applique from scrap materials. All this will only add originality to the door.

Features of restoration of metal entrance doors

Quite often, the front door loses its original appearance and becomes unattractive.

Today as front door They try to use iron, but in certain cases it can also be restored.

As a rule, restoration of metal entrance and interior doors requires certain skills and availability special tool, but you can do it yourself.

In most cases, an iron or metal door requires either replacement of the seal or facade finishing. In the first case, it will be necessary to remove the old seal and install a new one in its place.

If restoration of the facade of an iron door is required, then you need to decide on the choice of a new coating.

Even in those apartments where renovations have already been carried out, there are old, time-worn interior doors with minor defects or significant damage. Scuffs and scratches give a completely unaesthetic appearance to the interior of the room. There would seem to be only one way out - to update the door. However, buying a new product is often an expensive endeavor. Therefore, it is competent restoration that will help to get out of the current situation quite adequately.

Subtleties of the process

Old or damaged interior doors are subject to restoration. The cause of mechanical damage can be, for example, a fire. High humidity can also negatively affect wooden panels. Mechanical damage often occurs after opening the doors using improvised tools. When restoring a product, it may involve replacing the door leaf, updating the door jambs, painting or tinting the surface.

To restore functionality, it is often necessary to update the fittings or locks. In case of minor damage to interior doors, restoration work can be done with your own hands.

Repair original doors It is better to entrust it to a specialist in this field. The work should also be left to a professional if the restoration requires replacement door jamb or repairing the entire door frame as a whole.

For your information, some advantages and features of restoration of interior doors are presented:

• It is more profitable to repair doors made of solid wood, bringing them into proper and working condition, rather than spending your budget on a new product.
• Update old door when changing the interior style of the house. The procedure is carried out even when the canvas is still in excellent condition and does not yet need to be replaced.
• Restoration of old wooden structures is performed when the leaf and door frame self made, have a unique ornament and texture.
• Decorating the surface of the doors with your own hands will allow you to create a unique product that will harmoniously decorate the entire interior.

• An interior door must be repaired when replacing the door may compromise the integrity of the opening or wall cladding.
• By virtue of custom size It is better to carry out restoration work on an old door than to carry out a labor-intensive replacement of the product.
• Restoration is convenient, since replacing a product is often accompanied by replacing the entire door frame. This procedure will definitely create the need to seal the resulting cracks, plastering and gluing wallpaper around the doorway.

For independent work you will need a lot of free time. Step-by-step implementation of all procedures will be the key to successful restoration of the door leaf.

The successful use of techniques for restoring a product, first of all, depends on the characteristics and properties of the door leaf material.

Materials

Previously, interior doors were made exclusively from solid natural wood. Currently, door panels include polymers and glass. The surface can be coated with high-quality varnish or laminated. Oak doors or beech products are premium door leaves that have an elegant natural texture and come in a variety of shades.

Increased strength and durability make such interior products desirable and practical. Only the price due to these advantages is very high. Carrying out work on restoration of products much more economical than replacing the entire canvas.

The most popular material in the manufacture of canvases is fibreboard. Methods for restoring such doors differ from restoration work on solid wood products natural wood. To remove a layer old paint from the surface of a fiberboard product, an iron and a hair dryer are used. Considering the fine structure of the surface of the product, grinding work is carried out only using fine sandpaper.

Using finishing elements, slightly changing the surface relief, you can get an analogue of paneled fabric. Expensive models consist of dense tile material. The quality of the surface finish of the product determines the cost of the product.

Innovative veneer veneers are often used. The basis of the door will be inexpensive pine material, lumber or particle boards. Under the influence of temporary changes, veneered products may lose the integrity of the top layer. To restore such doors, special wood glue is required. When using glue one must also take into account the favorable temperature regime and avoid humidity. Violation of this regime can negatively affect the veneer surface, which leads to swelling and peeling of the material.

Not for everyone to use metal structures in the house. Iron doors also tend to wear out, unless, of course, these are armored products. Even on high-quality canvases it deteriorates over time external finishing, locks break, fittings fall apart. Long-term operation significantly affects the appearance and design mechanism of such doors. In iron interior designs Aluminum or stainless steel is mainly used. Metal parts successfully combined with other materials.

If you buy a new door, then high-quality hardware are expensive. Therefore, it will be much more profitable to repair the old door. Based on the experience of professionals, it can be noted that any type of metal door can be restored. Professionals can replace hinges, handles and locks in accordance with the color scheme of the door leaf to be restored.

Options for different models

One can confidently classify the “Stalinist” door as an antique. Indoor products from this era are usually double-leaf, often with glass inserts. In the “Stalin” style, the products are heavy and bulky, which makes restoration work a little difficult. Professional master can pick it up without any problems modern material for their cladding, necessary fittings and type of decoration.

Door leaves and the surface of historical “Stalinist” doors are usually wooden. If the cause of damage is not mechanical impact, then abrasions are the influence of time. Restored wooden doors should have an aesthetic appearance. Craftsmen will help you choose the main material and finishing material, giving a laconic look to antique doors.

In an apartment with a Provençal or Scandinavian style Interior restoration of doors is also decorative in nature. Finishing with patina and painting will turn an ordinary old white door into stylish element decor. The presence of frames and crossbars characterize the team interior door, which is also called paneled. For example, panels can be in the form of MDF sheets or glass inserts. This way it is possible to create figured elements and make the appearance of the canvas quite interesting. Restoration of paneled doors implies preservation of existing reliefs or complete replacement of the surface of the product.

This option is suitable for offices, bathrooms and toilets, balconies and other rooms with high humidity. Economical and moisture-resistant models are indispensable for such premises.

Glass is often used as an insert; there are also options for completely transparent doors for the newfangled living room interior, for example. Only types of special texture are used glass sheets. For safety reasons, the material must have a protective film and not form sharp fragments when broken, which is also taken into account when restoring such paintings.

How and with what you can update: ideas

Used to repair and decorate old or damaged doors. various materials. Color design The material provided is also varied. Complex work It is better to entrust door restoration and surface decoration to a specialist in this field. Remove minor scratches and simple work on decoration old surface it is possible to do it yourself.

An easy way to update a door is surface painting. Anyone can paint a surface. Both for painting and for other types of restoration, you first need to prepare the surface of the product. Cleaning and freeing the surface from the old coating will be the first step in restoring the product. Fine-grained sandpaper will perfectly remove old paint. Afterwards, small cracks and scratches are covered, then the type of coating and decorative elements are selected.

Available for painting in one color acrylic paint. In the case of restoration of a wooden door, paint and varnish are selected specifically for wood work.

Painting in several colors is a more complex process. To do this, using masking tapes, different shapes are created on the decorated surface. After applying paint over the created painting, an interesting geometric pattern is obtained. Different colors can be created by adding dyes to white base. The existing method of surface tinting will help create the effect of the presence of the most expensive types of wood in the composition of the canvas.

Special tinting impregnations - stains - will give the wood any desired color. As a rule, these are the tones of elite tree species. Due to this, the pine covering can be given a visual resemblance to walnut. Of course, it will only be external. Such properties as moisture resistance and resistance to rotting are not acquired in this process.

When painting, you also take into account the fact that wood tends to absorb paint a little during processing. Therefore, it will be necessary to apply another layer.

When working with paint, you can create not only plain doors, but also entire compositions. Designers will be able to recreate any design based on an original sketch if they apply it through a stencil. The idea of ​​restoration in the form artistic painting It’s also better to entrust it to professionals, since you can’t do it without artistic skills. Additionally, you can deal with protruding parts, that is, moldings. They also dye. For an original effect, they can be decorated in a contrasting tone.

In the case where the door is smooth, without relief or moldings, you can use an ornament to imitate their presence or stick on polyurethane carved slats. The slats must first be painted in the desired color.

The next stage of finishing is decorating the doors with wallpaper and fabric. In this case special restrictions no, because almost any images and materials of different textures can be glued to the door. First of all, you can pay attention to photo wallpapers, which are presented in abundance in specialized stores. Any paper materials, as well as standard wallpaper may also be useful.

It is necessary to ensure that the material is not too transparent. Otherwise, glue or hidden reliefs will appear. At the end of the installation using wallpaper, fabric or paper, it is recommended to apply a layer of varnish. This coating will protect the door surface.

Many models of interior doors have inserted glass, which is why stained glass design is very popular. Special stained glass paint is used to apply patterns and ornaments to glass surface. For independent work, materials for painting and stained glass work can be purchased at any specialty store. Drawings can be transferred to glass using sandblasting surfaces. A specialized workshop will be able to simply perform such work.

Pasting vinyl stickers as a way to decorate and restore a product is one of the simplest procedures. Vinyl door decals are sold almost everywhere. Protective covering can be removed without difficulty. Without preliminary preparation, the film is glued to the door leaf. After completing the work, the protective film on the outside. It is worth considering that vinyl stickers can even be painted.

The decoupage technique is also easy to perform and makes it possible to hide minor defects. In the process of this finishing, pieces of material, paper, napkins are collected into a single semantic picture, glued to the surface and covered with varnish.

The finishing option by building a picture from a mosaic is original and inexpensive; in the process, fragments of ceramics, glass, wood, and veneer are used. In addition to standard methods of restoring interior doors, you can use an extraordinary design method. Doors are renewed using various bulk materials. When pasting the surface with cereals, such as rice or buckwheat, you will get an exclusive and original work.

To secure the grains, you can purchase PVA glue. After complete drying, it is recommended to varnish the surface several times to protect it from moisture. Considering that the consistency of the cereal is dry, does not rot or deteriorate, and the varnish coating preserves the composition from moisture, there is no doubt about the durability of this design.

Restoration workshops

Minor damage can be corrected on our own and at home. To do this, it is necessary to properly prepare tools and materials for restoration. The stages of work are as follows:

• At the initial stage the door must be carefully prepared. To do this, the characteristics of the manufacturing material are taken into account. Basically, wooden products are subject to wear and tear. If the interior doors are covered with veneer, to work with the surface of the door leaf, you need to purchase wax that is soft in consistency, as well as a special varnish and a tool in the form of a spatula. For wooden products required use hard wax, coarse skin.

• Before starting work it is necessary Carefully remove the door from its hinges, fittings and locking device. If there are glass inserts, then they must also be removed, since all fasteners will be dismantled. It is better to carry out restoration work on the door indoors with sufficient lighting. Before placing the product in the workplace, it is necessary to protect flooring, since there is a risk of damage, since the paint from the damaged product will be removed under the hot air flow from the hair dryer.

• From the surface of the door it is necessary remove dirt by washing it soap solution. Afterwards the door is inspected for the presence of significant defects. Minor scratches can be filled with putty. Further wooden canvas wrapped in a flannel rag. The process begins by grinding the surface and removing excess wax using solvents. Next, it is recommended to varnish the surface.

• In any case, when working on the restoration of a door with a painted surface the old coating must be thoroughly cleaned. Doing this with your own hands is much easier than it might seem, since necessary tools All you need to do the job is a spatula and a hair dryer. The latter does not have to be purchased; currently it can be purchased for rent. If doors are decorated in the future, you should remember the trim and door frame. They also need to be finished to match the color of the door itself.

• After paint removal the surface is examined for scratches and other damage, they can be sealed with both putty and specialized wood putties. The final stage of preliminary preparation is sanding and grinding the surface. sandpaper. In order to protect the door from moisture, the sealed surface is treated with drying oil. Ordinary stain also has this property, which, in addition to protection, will give the surface a natural color.

03.09.2016 25389

Door restoration is the process of updating and restoring appearance and functionality. Most often in restoration, canvases are made of solid wood. They may appear scratches, abrasions and other mechanical damage. In addition, the tree can swell from high humidity. canvases are also susceptible to damage, in particular the appearance of scratches and cracks.

The need to restore doors

The door structure may settle and begin to touch the floor. If the wood swells from moisture, the door will have difficulty closing. Or, conversely, the door may dry out to such an extent that a visible gap appears between the door frame and the leaf. In this case, there will be a problem with locking.

If the door is paneled, the panels may become loose. The door frame may also need to be restored over time.

In addition to wear and tear, the canvas becomes unusable over time. Chips may appear, mechanisms may fail, and hinges may become loose. The roller mechanisms usually jam. In this case, the carriage mechanism and loose fastening are corrected.

Therefore, restoration of interior wooden doors may include the following types of work:

• carpentry;
• painting;
• finishing;
• decoration;
• reconstruction (for example, changing the opening mechanism).

Preparing for door restoration

Finishing work before restoration includes the following stages:

1. Restoration involves the appearance of dust and a specific odor, so before restoring an old door, you need to cover the furniture and other surfaces with polyethylene.
2. Before you restore an old wooden door, you need to get rid of the top layer of paint or varnish. This work is being carried out with the help construction hair dryer. In addition to the finishing coat, old layers of putty, screws and other foreign elements are removed. If there are partial chips, they must be completely removed if it is impossible to attach the chipped part to its place.
3. After removing visible imperfections, the door leaf is sanded with sandpaper. Now all cracks and chips can be corrected with a layer of putty. If you plan to varnish the solid wood, then the putty needs to be matched to the tone of the wood.
4. Sand the surface of the door leaf again. Now the door array is considered ready for final coating with paint and varnish material.

Cost of door restoration work

Below are approximate prices for the restoration of interior doors without taking into account the cost of materials.

Paint and varnish materials, putty, and tools will cost you from several hundred to several thousand rubles. It depends on the quantity of materials, manufacturer, quality. To save money, you can buy materials at a hardware store and update the door leaf yourself without contacting a specialist.

Do-it-yourself restoration of wooden doors

Restoration of old doors is carried out as the door leaf, its covering, and fittings wear out.

To update the door leaf you will need following materials and tools:

• drill;
• set of wood drills;
• fine-toothed wood hacksaw;
• construction hair dryer (or solvent for old paint);
• abrasive mesh for grinding putty;
• handle for attaching the abrasive mesh;
• putty for wooden surfaces;
• dye;
• brush.

Before starting repairs, it is better to open the windows and close the furniture to avoid covering it with a layer of construction dust!

Do-it-yourself restoration of wooden interior doors is a labor-intensive process, but quite simple.

The process of updating the door leaf takes place in several stages:

1. Remove the door from its hinges and lay it on a horizontal surface.
2. Using a hair dryer we remove old layer paints. Work is carried out at temperatures not lower than 400 degrees. Since heating is possible up to 6 thousand degrees, you need to work very carefully. First we heat it up small area surface of the door, and then remove the heated paint with a spatula included in the kit with a hair dryer. To avoid equipment failure, it should be used intermittently: 15 minutes of work, 5 minutes of rest.! In corners and hard-to-reach places, you need to carefully work with a spatula so as not to create new damage.
3. Primary sanding is performed to remove remnants of old paint and varnish materials.
4. Surface adjustment. This process involves applying a layer of putty. After it dries, the surface is leveled using a mesh attached to the handle. You need to sand in the direction of the wood grain, and not in randomly chosen directions. If you plan to varnish the door, then sanding should be done as efficiently as possible due to the transparency of the varnish.
5. We remove dust from the door surface and apply paint. It is better to apply two layers of paint (the second after the first has dried). Paint is applied along the grain, as is sanding.
6. Sand the door: remove particles stuck to the paint.
7. We tint the door with finishing paint (before this, matte, not very liquid, could be used as a base).
8. Installation of accessories.

If the old one's handle falls off or the lock jams, then the restoration of the interior doors will not be completed until you replace the worn-out fittings.

To replace accessories you will need:

• self-tapping screws (usually included in the hardware kit);
• screwdriver or set of screwdrivers;
• wood hacksaw;
• chisels;
• rulers.

If the door leaf is sagging, then do-it-yourself restoration of interior doors includes the following steps:

1. Check door hinges for looseness. If necessary, they need to be tightened.
2. If the hinges are not loose, you can try installing them a little deeper. To do this, the loops are removed. The area where the loop is attached is deepened with a chisel. The hinges are reattached with self-tapping screws.
3. If the sagging is the result of a change in the geometry of the door, then its shape is corrected with a plane (the same is done if the doors are swollen and do not fit door frame when closing). After adjustment, the door needs to be coated with paint.

If the door leaf has dried out, it can be restored by installing metal corners on it. Another option would be to sort through individual parts of the door leaf and collect them after restoration. The cracks can be filled with putty and the falling parts can be glued. The peeled parts need to be coated with glue and pressed with a press until completely dry.

Sometimes it is necessary not only to restore the door, but also the extensions, slopes and platbands. It is not difficult. The slopes are detached, and new ones can be placed on polyurethane foam. Polyurethane foam- This is a universal means for bonding any surfaces.

To make the foam dry faster, specialists sometimes irrigate open areas water from a spray bottle.

The platbands are nailed onto small nails with inconspicuous heads (you can choose nails to match the door).

Restoring old interior doors with your own hands is possible. Greatest difficulty constitutes the mortise of the lock. In this case, you can contact a professional. Other work does not cause any difficulties.

Now you know how interior doors are restored.

Situations often arise when the doors in an apartment or house are highly durable and reliable, but over time their appearance has become ugly and unpresentable. Don't rush and change the doors right away. To bring them back to normal condition, you can restore the canvas. To do this, it is not necessary to contact specialists - if you understand existing technologies, you can do all the work yourself.

Preparatory work for door restoration

Over time, doors lose their original appearance. Layers of paint gradually accumulate on them, which appear after each repair, and the time comes when the desire arises to remove and throw away the doors. But there's no need to rush. If the canvas is durable and reliable, then its appearance can be updated. There are many ways to carry out restoration work. When choosing a restoration option, you need to take into account the design of the room, since the doors must fit harmoniously into the interior of the room.

There are several reasons why it may be necessary to restore doors:

• mechanical damage to the surface. Over time, cracks, scratches and chips gradually appear on the canvas and door frame, which spoil their appearance;
• temperature changes and high humidity. These factors also negatively affect the condition of the door.

Before proceeding with restoration, it is necessary to carry out preparatory work:

1. Removing the door leaf. It must be removed and placed on a horizontal surface. If the hinges are removable, then it is enough to lift the door and remove it from the hinges. If it is installed on permanent hinges, you will have to unscrew them.

   To remove the door leaf use special devices or improvised means

2. Removing fittings. Carry out restoration of the canvas with installed handles, locks and hinges will be inconvenient, so they need to be dismantled. If there was trim or glass inserts on the door, these must also be removed.

   All hardware is removed from the door

3. Removing old paint. This is the most difficult stage of preparatory work. It is necessary to remove the old coating as efficiently as possible, otherwise it will not be possible to obtain a new, beautiful and smooth surface. There are several ways to remove paint from a door leaf:
   • manually using sandpaper - this is a labor-intensive method that takes a lot of time;

     Manually removing paint is difficult and time-consuming

   • using a grinder or electric drill and an attachment with sandpaper;

     The paint is removed with a grinder or electric drill with a special attachment installed.

   • a grinding machine - this option is suitable when the surface of the door is smooth;
   • using a hair dryer and a spatula. The surface of the canvas is gradually heated with a hairdryer, the paint begins to swell, after which it is removed with a spatula;

     Use a hairdryer to heat the surface, then remove the paint with a spatula.

   • with help gas burner or a blowtorch. You must be very careful not to damage the wooden panel. During the work there will be a burning smell, so it is better to do it outdoors;

     It is better to remove paint outdoors using a gas torch.

   • special solutions. Such compositions are applied to the painted surface for some time, after which the paint swells and is removed with a metal spatula. You can make such a solution yourself by mixing oatmeal, caustic soda and water. The resulting composition is applied for 40 minutes, after which it is removed along with the paint.

     Paint is removed using special solutions

Basic methods of door restoration

The result of the restoration largely depends on how well the surface is prepared. Old paint must be removed slowly and carefully to completely remove it. When all the preparatory work has been completed, you can begin processing the door leaf.

To complete the work you will need the following tools and materials:

Sanding and painting

This is the simplest and most available method restoration. After high-quality surface preparation, the door leaf is painted in the selected color.

Sequence of restoration work:

1. Surface grinding. After the paint has been completely removed, the surface is treated with sandpaper. This can be done using a grinder, an electric drill with a special attachment, or grinder. To polish the surface efficiently, you need to use sandpaper of different grain sizes. First, coarse-grained sheets No. 100 and 200 are used, and then fine-grained sheets, No. 400 and larger.

   Sandpaper of different grits is used to sand the surface.

2. Elimination of defects. After sanding, deep cracks or scratches may remain on the canvas, which must be eliminated. To do this, use wood putty. After it has dried, the canvas is again treated with sandpaper. You can make the putty yourself by mixing fine wood dust and PVA glue. You need to polish the doors especially carefully when you plan to varnish them. In this case, even the slightest irregularities and defects will be visible, and this will spoil the appearance of the restored door.

   All cracks and scratches are repaired with putty.

3. Coloring. Before you start painting the canvas, remove all dust from it with a damp cloth. After this, allow the surface to dry. To properly paint doors, you need to apply at least two layers of paint. First, it is recommended to paint the canvas in White color. After it has dried, the surface is treated with fine sandpaper and the dust is removed again. All that remains is to cover the doors with matte paint of the required tone. Depending on what tone saturation you want to achieve, apply different quantities layers.

   Paint can be applied with a brush, roller or spray gun

Video: painting the door

You can decorate the door leaf, but if you do not have such talent, then ready-made stencils are available for sale. The work is performed in the following order:

Video: stencil for a door

Textile Application

Instead of dyeing the canvas, it can be covered with fabric. Different fabrics are used for this, but we must remember that all surface imperfections will be visible through thin materials.

Door finishing with textiles is carried out in the following order:

Wallpapering

Wallpapering a door was very popular before, but fashion is constantly moving in circles and now this method is also often used for restoration.

Wallpapering the canvas is done in the following order:

Video: pasting a door with liquid wallpaper

Decoupage

Decoupage is a common technique that even a beginner can master. Such restoration is carried out as follows:

1. Surface primer.
2. Painting the canvas. First it is rubbed with paraffin and then painted.
3. Decoupage door. You can use ready-made decoupage cards, printed pictures, multi-layer napkins:
   • think over the location of all the details. You can put discreet marks on the canvas so you don’t forget where to glue what;
   • Drawings are cut out along the contour. When using multi-layer napkins, carefully separate the top layer;

     It is necessary to carefully separate the top layer of the napkin

   • the finished picture is applied to the dry surface of the door and covered with PVA glue diluted with water;
   • smooth the material. In order to remove air bubbles, it is recommended to move from the center to the edge. To glue a large canvas, start working from top to bottom;
   • the doors are varnished. To make the decoupage look more beautiful and the service life of the coating to be as long as possible, after the glue has dried, 1-2 layers of varnish are applied to the doors.

     To decoupage the door, you can use ready-made cards, napkins, photographs or newspapers

Video: door decoupage

Lamination

It is difficult to make high-quality door lamination at home, but in this way you can quickly update the appearance of the canvas. For this, a special film with a self-adhesive base is used.

The work is performed in the following order:

You can not completely cover the canvas with film, but use a variety of vinyl stickers. Construction stores have big choice, so you can design the canvas in accordance with the interior of a particular room.

You can not completely cover the door, but use vinyl stickers

Decoration

In order to make the door leaf original, it can be decorated. One of the most simple ways is to paint the door one color, and its protruding parts another. Polyurethane or wooden slats can be attached to a smooth surface.

Wooden or polyurethane slats are fixed to the door and painted in a contrasting color

You can decorate the canvas using designs made from bulk materials, the most accessible of which are rice, buckwheat and colored sand. To glue the grains, use wallpaper glue or PVA. After the canvas has dried, it is coated with several layers of varnish to secure the design. In addition to bulk materials, doors can be decorated with shells, fragments of broken dishes or other unusual items.

To decorate a door with a buckwheat pattern, coat the canvas wallpaper glue or PVA and throw cereal on top

Overlay facades

Simple and in an accessible way restoration of the door leaf is the installation of overhead facades:

Canvas update

If the door leaf has a glass insert, you can update it in the following ways:

Video: creating a film stained glass window

If you look into the issue, it becomes clear that door restoration is not such a complicated process. You can change the appearance of the door different ways depending on the financial capabilities, preferences of the owners, as well as the interior of the room, since the doors must be in harmony with the surrounding environment. By choosing a restoration method and studying the sequence of restoration work, you can restore the condition of the door yourself.

Despite their unlimited service life, they wear out quite quickly. The material suffers from deformation and drying out, coatings wear off or become faded.

You can replace such canvases with new ones, but this is a big expense, a waste of time for replacement, and subsequent renovation work after installing them.

Therefore, the easiest way is to put these structures in order yourself, that is, give them a second life by updating their coating and eliminating defects. How to restore old doors? More details later in the article.

In order to restore doors correctly and efficiently, you need to know how it is done.

Typically, interior fabrics suffer from mechanical stress and moisture.

Plastic varieties are more prone to scratches.

To make them invisible, they must be gently polished.

• Painting. A wooden door or one with veneer inserts is easiest to varnish or paint. It is better to paint a wooden surface using a special brush or spray. A wooden surface should be painted and varnished by brushing along the fibers, then the material will lie smoothly, filling all the unevenness, chips and other defects.
• Decoration. To give the updated canvas brightness, you can use other shades to create a new image. You can paint the canvas with one color, and the protruding parts with another, contrasting with the main selected shade. If the surface is smooth, then it is recommended to use carved slats made of wood or polyurethane, gluing them to the surface to be treated, after painting them in a suitable color.
• Pasting using rolled wallpaper, colored paper or fabric. They often offer to stick special photo wallpapers onto a smooth canvas, which are sold in stores or can be easily purchased online. The design can be styled to match the room. For the nursery, drawings and reproductions from children's magazines are selected. For the kitchen, choose pages with dishes or vegetables and fruits. Before gluing paper sheets They need to be kept in water, then PVA glue is applied to the entire sheet and glued to the canvas, smoothed thoroughly. After the paper and glue have dried, the surface is coated with colorless varnish to preserve the work longer. In the same way, you can cover the surface of the old material with fabric.
• Vinyl stickers. When pasting vinyl stickers It is not necessary to clean the canvas from old paint and eliminate irregularities. The stickers will hide all the defects, and you can paint them after that. They must be glued onto a degreased surface, after cleaning the area with an alcohol cleaner. Remove the backing from the sticker and apply it to work area, smooth out thoroughly. Only after this can you remove the film protecting the front side.
• Cereal decorations. In an original way decoration of an old door is considered to be an image of drawings made from bulk materials. Rice and buckwheat are ideal for this. The grains should be glued using PVA glue or standard wallpaper. After the drawing has dried well, the canvas is covered with several layers of colorless varnish. Dry cereal, and even under a layer of varnish, is stored for a very long time.

With a little effort and imagination, there will be no need to figure out how to restore old doors at home. Updated interior doors will add warmth and comfort to your home, and also improve the interior of the apartment.

Updating an old door with glass

How to restore old doors with glass is not an idle question at all.

Glass becomes cloudy over time, acquires scratches, and therefore when updating it must be restored or replaced with a new one.

To remove old glass, you need to carefully remove the glazing beads that hold it in place.

You can replace the glass with a modern one: frosted, corrugated, colored, with a pattern or photo printing.

To correctly insert new glass into the door leaf, you must do the following:

• Measure the parameters of the opening in the door leaf where the glass will be inserted.
• Cut the glass to the required size so that it can fit securely into the opening, for which it must be 5 mm shorter than the required size on each side. To cut out a piece you will need a glass cutter and a metal ruler.
• Insert the glass into the opening, previously treated with sealant, and secure it with glazing beads, securing them with thin nails.

Glass with hidden fixation more difficult to insert, will require complete disassembly with unscrewing the bolts in order to pull out the old part and also insert the new one. The negative aspect of such a replacement is the possibility of losing the correct dimensions of the canvas. In this case, it is necessary to straighten it using a plane.

If you insert old glass, it must be brought back to normal. Clean the old one with a scraper, acetone or blade. Polish small scratches using toothpaste.

Renew the glass with a film with a pattern, paint it or make a stained glass window on it. It is necessary to use fresh glazing beads and replace the fittings with new parts.

Instead of glass, you can insert an acrylic unbreakable mirror. It is light and durable, easy to cut and highly decorative. Then the door will look like new and will delight residents for a long time.

Fiberboard canvases

This canvas is slightly different from working with wooden surfaces. The thickness of the fiberboard surface reaches only 4 mm, so it is necessary to remove paint from it with extreme caution.

You cannot use a blowtorch for this - you can use an iron, wrapping it in a towel if you don’t have a hair dryer.

After sanding, the canvas is either varnished or painted with new paint. But there is a restoration method that allows you to turn a thin canvas into a natural wooden door - this is veneering the canvas.

Veneer parts are sold in special stores. You can glue it using an iron, heating the surface, because it already has an adhesive base.

You should act carefully so as not to overheat and burn. The glued parts can be treated with stain and varnished. Decorate simple door can be done by gluing relief strips onto its surface.

We should not forget about the restoration of the door frame - it must correspond to the updated canvas. By replacing the fittings with new, more modern ones, you can increase the service life of the door.

Plastic products

Most assume that it will last forever and its dazzling snow-white appearance will not fade. However, even plastic products will eventually require replacement or restoration.

An old plastic door can be restored in several ways:

• Painting the door. First you need to remove the old protective film from the plastic. Then wash the surface well using special products. The main difficulty in applying paint to plastic is that the liquid in pure form cannot be applied. You should add a little hardener to the paint and then filter it. To the surface plastic products The paint is applied using a spray gun in one layer. Next, let the paint dry and install the door in place.
• Vinyl film sticker. If you don’t have the opportunity or desire to paint, you can stick vinyl film on the old door by choosing the appropriate pattern and color. To ensure high-quality gluing of the film, the surface of the plastic must be degreased and then washed with soapy water. Apply the film to a clean and dry surface and smooth it, after a few seconds you can remove the white base.
• Veneer covering. Also treat the surface of the door and glue the veneer parts onto it using a hot iron. This option is acceptable and reliable. Natural material lasts longer than artificial panels.

Don’t forget to update the door frame, because it cannot be replaced; gaps may form between the frame and the door leaf. The fittings also need to be replaced and the door will be like new.

What about metal?

You can update not only the interior doors, but also the entrance doors made of metal. To do this, it should be removed and placed on a horizontal, flat surface, this will make it more convenient to work. Then execute in the following sequence:

• Remove or close construction tape accessories: peephole, handle and other components.
• Use a drill or wire brush to clean areas damaged by corrosion. Sand the surface of the canvas with coarse sandpaper, remove dust with a vacuum cleaner and treat the canvas with a solvent.
• Treat the surface with a special polish compound, but intended for cars. Putty cannot be used for wooden products - it gives poor adhesion to the metal surface. Car polish will repair all dents and scratches that occurred during the rust removal process. Give a smooth surface using a spatula and let the canvas dry for 30-40 minutes.
• Polish the restored surface with fine sandpaper, wipe with a damp cloth and degrease using a special construction grease remover.
• Prime the surface with a metal primer designed to combat corrosion. It is convenient to apply it with a roller or narrow brush. Let it dry and sand again with fine-grit sandpaper.
• Paint the surface with the chosen paint in 2-3 layers - it is important to achieve the desired rich result. Each new layer is applied only after the previous one has completely dried. For painting it is recommended to use a roller, brush or spray gun. You should protect yourself from paint exposure by wearing gloves and a respirator.

The door frame should be restored in the same way.

Then remove the fittings from the tape or reinstall them and hang the door in its place.

If only a section of the canvas has been damaged, you can renew only that area, although this will require careful selection of paint according to tone.

Restoring old doors with your own hands is an interesting and exciting job.

You can choose an acceptable canvas, choose suitable material and get creative with the decor.

In addition, you can save significantly on replacing doors, and this is an important fact for the family budget.

Do-it-yourself updated doors are a source of pride for the owner of the house. You can see how to repair them in the video: