If the old bathroom has served its purpose, do not rush to throw it in a landfill or sell it for scrap; you can use it to make a rather original and creative sofa with your own hands. Such a sofa can become a decoration for any home, from an apartment to country house, it will also fit well into the interior of various salons and offices providing services.
To make such a sofa, an old cast iron or metal bath, although it is better to give preference to cast iron, it has good stability and original form especially if it is an old model. Making a sofa from a bathtub is quite simple, all you need is an old bathtub, a corner one Grinder(Bulgarian) with cutting wheels for metal and sanding attachments, enamel paints for painting bathtubs and foam rubber with fabric for seats and pillows.
After removing the legs, we clean off the damaged and peeling areas of paint and enamel.
Having laid the bathtub on its side, we draw the expected shape of the sofa frame; here everything depends on the wishes and your own fantasies. Cut lines can be straight, oblique, patterned, semicircular, etc.
We carry out cutting with a grinder and do not forget about personal protective equipment.
Having cut out the excess part of the bathtub, we sand the cut line to remove burrs and make it more rounded. You can paint with any paints intended for metal base, these are all kinds of enamels, nitro paints, aerosols and the like.
The legs in such bathrooms are overhead and self-tightening under the weight; they need to be cleaned, painted and put into the groove inserts. In case of their absence, you can weld the necessary frame from pipes or angles and install it in it; you can also make stands from stone or wooden beams.
Making a seat is enough simple work, take foam rubber of suitable thickness and cut out the required shape from it.
We wrap the cut-out foam rubber blank with padding polyester or spandbond.
Then we cover it with a cloth; if possible and desired, you can sew a cover and insert foam rubber into it.
You can sew the pillows for the back and side armrests yourself or purchase ready-made ones in the store that are suitable in color and size.
Here you can see that the seat base is made from wooden planks, which in turn can be covered with a blanket, blanket or soft blanket.
In this option, the entire interior is covered with foam rubber and a one-piece cover is sewn.
A padded backrest and headrests will give this sofa a businesslike look.
The right combination of colors and colors will give the sofas a unique glamor.
By cutting the bathtub in half, we get two original and quite comfortable armchairs that will become an effective addition to your sofa made of old bath with your own hands. Requirements for the top rating of casinos in 2019 are here http://www.wowmagic.ru/kazino-zerkalo/top-rejting-onlajn-kazino/ How to choose the top casino?
Do it yourself
Do-it-yourself door upholstery
After overhaul there is a lot of old stuff left in the house building material, including wooden doors. We offer one of the options for how to frame a door with your own hands....
How to make a sofa
Every person can make a sofa on their own, even with minimal carpentry skills, just a little skill in using construction tool And...
First you need to remove the legs (if any) and clean off any loose paint and enamel using a sander.
Step 2
Then turn the bath over to mark the cutout for the future sofa. The shape of the neckline can be smooth, sharp, semicircular, it all depends on your imagination and wishes.
It's worth cutting with a grinder and a cutting wheel for metal. Work with this tool very carefully, take care of protective equipment in advance.
Step 3
After the cut is ready, the cut should be sanded to remove sharp edges and burrs. After which you can start painting the future sofa. To do this, use any paint intended for metal (enamel paint, nitro paint, aerosol paint, etc.); you can use several paints to decorate the sofa, draw any pattern or design, applied with your own hand or using a stencil.
Step 4
The legs can also be painted in any color and installed in their original place. You can use stones or wooden beams(or stumps).
Step 5
For softness and comfort, you can make a seat from foam rubber, cut to the size and shape of the bathtub. Wrap the resulting form with padding polyester. You can sew a cover for a foam seat or simply wrap it in fabric and place it on the bottom of the bathtub. You can also sew or purchase pillows under your back, which will make your stay on such a sofa even more comfortable.
If the old bathroom has served its purpose, do not rush to throw it in a landfill or sell it for scrap; you can use it to make a rather original and creative sofa with your own hands. Such a sofa can become a decoration for any home, from an apartment to a country house, and it will also fit well into the interior of various salons and offices providing services.
To make such a sofa, an old cast-iron or metal bathtub is suitable, although it is better to give preference to a cast-iron one, it has good stability and an original shape, especially if it is an old model. Making a sofa from a bathtub is quite simple, all you need is an old bathtub, an angle grinder (grinder) with cutting wheels for metal and sanding attachments, enamel paints for painting the bathtub and foam rubber with fabric for the seat and pillows.
After removing the legs, we clean off the damaged and peeling areas of paint and enamel.
Having laid the bathtub on its side, we draw the expected shape of the sofa frame; here everything depends on the wishes and your own fantasies. Cut lines can be straight, oblique, patterned, semicircular, etc.
We carry out cutting with a grinder and do not forget about personal protective equipment.
Having cut out the excess part of the bathtub, we sand the cut line to remove burrs and make it more rounded. You can paint with any paints intended for a metal base, these include all kinds of enamels, nitro paints, aerosol paints and the like.
The legs in such bathrooms are overhead and self-tightening under the weight; they need to be cleaned, painted and put into the groove inserts. In case of their absence, you can weld the necessary frame from pipes or angles and install it in it; you can also make stands from stone or wooden beams.
Making a seat is a fairly simple job; we take foam rubber of a suitable thickness and cut out the required shape from it.
We wrap the cut-out foam rubber blank with padding polyester or spandbond.
Then we cover it with a cloth; if possible and desired, you can sew a cover and insert foam rubber into it.
You can sew the pillows for the back and side armrests yourself or purchase ready-made ones in the store that are suitable in color and size.
Here you see that the base of the seat is made of wooden boards, which in turn can be covered with a rug, blanket or soft blanket.
In this option, the entire interior is covered with foam rubber and a one-piece cover is sewn.
A padded backrest and headrests will give this sofa a businesslike look.
The right combination of colors and colors will give the sofas a unique glamor.
By cutting the bathtub in half, we get two original and quite comfortable armchairs, which will become an effective addition to your sofa, made from an old bathtub with your own hands.
Old cast iron bath- a valuable item, so throwing it away or scrapping it is not the wisest thing to do. Experienced gardeners They take the bowl to the dacha and use it to make things useful for the household. Several examples of using a font will be useful for novice gardeners.
Why you shouldn't throw away your old bathtub
Cast iron hot tubs are extremely practical products with a service life of at least 50 years. The material resists corrosion thanks to a special protective film easily tolerates temperature fluctuations, does not emit harmful substances into the ground.
When the enamel layer is peeled off, the defect area is cleaned and covered with acrylic paint.
Here are some advantages of cast iron hot tubs:
- capacity;
- high degree of tightness (if you plug the holes);
- high sides;
- presence of holes.
And now about how bathtubs are used in the country.
Country furniture
The smooth shapes of the walls and bottom are a ready-made frame for constructing armchairs and a sofa. From one bowl you get 3 pieces of furniture - a pair of chairs and a table. There will only be one sofa.
They do this:
- mark three equal transverse cuts along the entire horizontal plane;
- the outer pieces with walls and a transverse bridge are armchairs;
- middle - table (turn over and place on the walls).
The edges are sanded, the seat is equipped with a warm mattress or pillows - ready. Exterior decor is to the taste of the owner - painting, mosaic. To make a sofa, cut out one large wall, leaving the other three walls. The cuts are also polished, and a soft bedding is made on the seat.
To prevent the legs of the bathtub from pressing through the soil or wooden floors, thick pieces of rubber stopper are placed on them.
Flower garden
The most difficult thing is to choose the location of the future flowerbed, the rest will take just a couple of minutes:
- plug the bottom;
- lay out a layer of large pebbles;
- pour some sand;
- fill the bath with soil;
- plant flowers.
All is ready. The outer surfaces are decorated with broken tiles and stones - fixed with Moment glue. The walls are painted, painted and even made into a “slide” - pots with flowers are placed on the soil so that they grow to the edge of the bathtub and cover the outer walls.
On limited area plot in the bathroom, a multi-tiered flower bed is being built. They put up a frame with shelves, stretch the film and install boxes with flowers. The soil in the bowl is the first level, the rest are raised by shelves to the required height.
If you install a bathtub in the corner of the garden adjacent to the wall, and use a cascading fountain, the relaxation zone will make you forget about gardening chores forever.
Water container
Plug the drain and overflow holes, fill the bowl and let it sit in the sun. Warm water is much better for irrigation than cold water. Plants do not experience stress from temperature changes; soft, settled moisture will not burn young bushes of crops. To prevent the device from looking too provocative, the sides are painted, covered with film or decorated in some other way.
When choosing colors, preference is given to dark shades - they conduct heat better and the water will heat up faster.
Warm high bed
A sore back and knees do not allow you to stand in the beds for a long time - take a bath. To make it high warm bed for any crops, take:
- almost an entire bathtub (old ones with chipped enamel layers are perfect);
- paint the walls with dark paint;
- do not plug the drain and make a couple more holes in the bottom ( hammer drill it will come in handy);
- a layer of pebbles is placed on the bottom;
- a layer of sand is poured onto the pebbles and leveled;
- lay out a layer of old newspapers, compost or even artificial carpet - the insulation is ready;
- pour nutrient soil.
Any crops can be planted - even capricious eggplants will quickly grow on such soil. The high sides of the bathtub allow you to care for plants without bending over.
To get rid of weeds, the surface of the bed is mulched with newspapers and straw. The coating will not allow weeds to pass through, but will not interfere with the growth of zucchini, tomatoes, etc.
Greenhouse
The high bed from the bathtub is covered with a frame of twigs and the film is stretched - the greenhouse for cucumbers is ready. The frame is made to the required height, and lutrasil is used instead of film. The membrane will provide ventilation, but will not let cold air through to the plants. Cucumbers grow especially well in such greenhouses.
Pool or pond
Of course, you won’t get a large pool from a bathtub, but kids will be able to happily splash around in the warm water on fresh air. The principle of constructing a pool or pond is the same:
- Dig a hole of the required depth. Sand is poured onto the bottom so that the bathtub stands tightly and does not wobble.
- The bath is lowered into the hole, the gaps between the walls of the container and the soil plumb lines are filled with earth.
Now water for the pool is drawn into the font - by pulling the hose through the overflow hole. To build a pond, flowers in pots are lowered to the bottom, fountains are built, etc. Visible surfaces and the soil around the bowl are also decorated in any chosen way.
The depth of the pit depends on the height of the sides of the font and the wishes of the owner. The standard is considered to be a depth of 2/3 of the wall height.
And more options for using a bath in the country:
- container for bulk building materials;
- a table with a cabinet - they put a lid on the bathtub, under it they put everything that is needed for tea drinking, marinades or something else;
- grill - a grate is installed on the sides and a fire is lit under it;
- container for storing equipment, compost, etc.
To build a multi-tiered stove, the font is placed on the side wall (short). Now the container is marked, in the lower part there is a firebox, and in the middle there is a barbecue or stove for cooking lunch.
If you have an old bathtub, don't rush to throw it away. You can make a nice chair out of it, or even two. Everything is done quite simply, you just need to attach greatest number strength to cut the bathtub and weld the support. Let's look at the manufacturing process in more detail.
Materials and tools for homemade:
- old bath;
- support from an old chair;
- bolts with nuts for fastening the support;
- dye;
- sandpaper for grinding the metal surface;
- Bulgarian;
- welding;
- spanners;
- a piece of steel plate;
- LED strip (optional).
Chair manufacturing process:
Step one. Preparing the bath
First you need to clean the bathtub from dirt. The author had livestock drinking from the bathtub, so there was quite a lot of dirt in it. We pour out the dirt and wash it so that the material is comfortable to work with and does not get dirty.
Step two. Marking the locations of the incisions
Take a pencil or marker and draw a line for the future cut. As for the sizes, then decide for yourself. The bathtub needs to be cut at an angle, as the author did.
Step three. Cutting a bath
We take a grinder with cutting discs and cut the bathtub. There is no need to rush in this matter, take your time, use safety glasses and gloves.
Step four. Chair base
As the basis for the chair, the author used a support from an old office chair. This chair is old, so the support is not made of plastic, like modern ones, but of metal. We cut off the excess and prepare a plate for attaching the chair.
Step five. Attaching the support to the seat
We weld the fastening nuts to the metal seat. Thanks to them, the support can be removed if necessary, that is, the chair is collapsible. Drill four holes in the metal plate of the support; bolts will be screwed into them.
Step six. Cut off excess from bolts
In order to be able to fasten the support with the bolts, they need to be shortened. We take a grinder, clamp the bolt in a vice and cut off the excess. Trim the cut edges so that the screws fit into the nuts without any problems.
Step seven. Trial assembly
At this step you can already assemble the chair. You need to make sure that the chair is assembled smoothly and securely.
Step eight. Aligning the curve of the bathtub
So that no one can see the bathtub in this chair, you can seal the bend. For such purposes, take two steel plates and weld them into in the right places. First, tack by welding, and then finally weld.
Step nine. Preparing metal for painting
Painting a bathtub is not so easy, because not every paint sticks to the enamel. The essence of preparation is to make the surface matte. This can be achieved by using an angle grinder with grinding disc. You can also work sandpaper and other means. Finally, the entire surface was wiped steel wool.
Step ten. Primer and painting
First of all, we apply a primer; the author has both paint and primer in cans. Well, then, when the primer has dried, apply two layers to the surface acrylic paint. You can use gloss or matte paint.
Step 11. Clean and polish the support
The author polishes the support from an old chair to a shine.
Step 12. Edging the chair
To prevent the chair from being cut and to look more solid, the author adds edging along the edge.
Step 13. LED strip
Since the author made the chair for his son, who is interested in computer games, it was decided to equip it LED backlight. The author used for such purposes LED strips. We glue it to the chair, and also connect the power source, which is the batteries.