Many people in summer time prefer to leave stuffy city apartments and spend time on suburban areas. However, the absence of such a benefit of civilization as a shower can significantly spoil the impression of even the best outdoor recreation. The solution to this problem is an outdoor shower, the construction of which is the subject of this article.
General information
Building an outdoor shower yourself is not at all difficult, and you don’t even need to spend a lot of time on it.
All you need is:
- Prepare a tank of suitable volume;
- Make the frame of the future shower stall;
- Cover the frame with any sheet material.
The main part of the work is making the frame. If you know how to work with a welding machine, then the best option there will be a frame made of profile pipes. This material is inexpensive, strong and quite durable.
Advice! If it is not possible to make a shower from pipes, you can use a wooden beam pre-treated with an antiseptic for this purpose.
Below we will look at how to build a summer shower from pipes.
Construction Features
Materials
So, to build a summer shower from a profile pipe, you need to prepare the following materials:
Selecting a location
Before starting construction, you need to decide where the country shower made from a profile pipe will be located.
The following requirements apply to the site for future construction:
- It is advisable that the shower be located on a hill, which will improve the flow of water. If there is no such place on the site, you need to dig a drainage hole.
- The place should not be shaded, which will allow the water to quickly heat up in the sun.
- If there is a well on the site, the distance from it to the future shower should be at least 8 meters. In addition, the shower should be located at a sufficient distance from the foundation of the house.
Project preparation
Any construction, as you know, begins with the preparation of a project, and the construction of a summer shower is no exception. At the design stage, it is necessary to determine the size of the future structure and its design.
Most often, summer showers have the following dimensions:
- Height - 2 -2.5 m.
- Length and width – 1.5 m.
Of course, you can change the dimensions if you wish. For example, many increase the area of the building and equip it with a locker room. The latter can be separated from the shower with a curtain or partition.
Preparing the base and drainage pit
Construction should begin with your own hands by preparing the drainage pit and foundation. The size of the pit depends on the number of people living. The pit should be located close to the booth itself, for example, behind it.
The bottom of the pit must be filled with sand and gravel, and the walls are lined with stone or brick. When the pit is ready, you need to make a foundation with a drain.
The work is carried out in this order:
- First of all, you need to prepare the site - remove debris and grass.
- Then it is laid so that it goes into the hole at an angle. It is best to place the drain in the center of the shower stall.
- Next, you need to mark the future site and make formwork from boards or other material along the contour.
- After this, the bottom of the formwork must be covered with a layer of crushed stone and compacted.
- Then supports are installed at the corners of the formwork. To do this, the pipes need to be driven 20-30 centimeters into the ground. The racks can be positioned vertically or at a certain angle, as shown in the diagram.
- After installing the racks, a metal reinforcing mesh should be laid, which should rise slightly above the surface of the crushed stone.
- To complete the work, you need to fill the formwork with concrete.
Frame making
When the concrete hardens, you can make a frame for a summer shower from a profile pipe. Since the concrete screed will not be subjected to heavy loads during operation, it is not necessary to wait 28 days for the concrete to gain grade strength.
The manufacture of the frame begins with the construction of a frame for the tank. To do this, you need to connect the racks along the perimeter, as well as diagonally. Then the racks must be connected with cross members located on three sides, which will add rigidity to the structure.
At this point, the frame for the shower from the profile pipe is ready, now you can start arranging it and covering it.
Shower arrangement
The arrangement of the shower begins with the installation of the tank. It is desirable that the container be flat and wide. In specialized stores you can purchase a special tank for a summer shower with installed fittings.
If the container has enough surface area, it can serve as a cabin roof.
Otherwise, you will first need to lay the roofing material.
- A fitting should be cut into one of the walls of the tank, which will face the cabin.
- After installing the tank on the roof, it is attached to the fitting ball valve and a shower head. The water supply is regulated by a ball valve.
Advice! To make the water heat up faster, the tank should be painted black.
Hot weather is a rarity in most of our country. On cold days there is simply no way to heat the water in the container to the required temperature. There are not many people who want to take an ice-cold shower.
By country shower, most people mean simple design with a barrel on the roof. This shower has the following disadvantages:
- the water in the container blooms very quickly;
- there are constant problems with filling the barrel;
- it is impossible to maintain the desired water temperature.
To realize your idea, you need to familiarize yourself with the advice of craftsmen. Country shower will allow the family to comfortably take water treatments.
The mobile shower works according to the following principle. Any container is installed next to the device. This could be a bucket or basin. Warm water is poured into it. After this, the end of the hose is lowered into the container.
The device that pumps water into the shower looks like a rug. A hose with a watering can is connected to one end of the pump. In this way, you can get a stream of water that will flow while stomping on the mat. This option is convenient because a mobile shower can be used not only in the country. The device will be useful for people who want to maintain hygiene while hiking. Even in such spartan conditions you can wash yourself. The advantage of such a shower is the ability to adjust the water temperature.
How to make a summer shower at the dacha with your own hands - for construction reliable design carefully select photos and sizes.
When building a stationary shower, the owner needs to decide where to divert the water. If there is already some kind of drainage hole on the site, then you can drain the water directly there. But that's not the most The best decision, since many people use bacteria to process wastewater. An increase in humidity will have a negative impact on the rate of purification of contaminated liquid.
During the construction of a shower room, it is best to make a separate drainage hole. To strengthen the bottom of the hole, you can use broken bricks.
It is most difficult to strengthen a hole dug in sandy soil. Its walls will be eroded by wastewater during operation. Therefore, it is necessary to line the walls of the sandy depression with boards.
The owner can save money when building a shower due to materials. To build a shower there is no need to build. When constructing a foundation, foundation blocks are most often used. They are leveled and the shower is raised 20 cm above ground level.
This height is enough to prevent the treated wood from rotting. When constructing a foundation, it is not necessary to use wood at all. You can weld a metal body and place it on paving slabs. If desired, you can strengthen the base by filling it with concrete.
There are no specific standards regarding the frame. A shower cabin, as a rule, consists of several parts. In one compartment you can arrange a locker room. There is a water heater in another room. It can use wood as fuel.
A room for storing equipment can be attached to the shower. If you are planning a lighter structure, then you can use the following option - instead of a door, hang a curtain. This will make the design easier and reduce construction costs. Be sure to take into account the height of people who will use the shower. Optimal height should be 2.2 meters. The width of the structure must be at least 0.9 meters. When making a frame, you can use not only metal, but also wood.
To make a metal frame, it is advisable to use corners with a thickness of at least 4 millimeters. The width of the shelf depends on the load. The frame will hold the water tank. What to do if you plan to supply a plastic container with a volume of 100 liters?
In this case, it is necessary to carry out the procedure of covering the shower stall on both sides with special clapboard. This material is considered the most practical. It has an attractive appearance and can withstand for quite a long time. humid environment. But for this it is necessary to treat the lining with a special solution.
To do metal carcass you can use scraps metal pipes. The pipe wall thickness must be at least 3 mm. Otherwise, the shower structure may not withstand the load.
The frame can be strengthened using lathing. To do this, weld additional corners to the structure. With absence welding machine can be fixed with bolts.
To build a shower in the country with your own hands, you need to calculate the volume of the tank. For a family of 4 people you will have to supply a barrel with a volume of 100 liters. To make a wooden frame, you can buy timber. The beams are fastened using a tongue-and-groove system.
You can build a summer shower for your dacha with your own hands without using expensive materials.
Film is considered the cheapest material for covering shower walls. The disadvantage of this option is that the service life is too short. In a year you will have to buy new film. Therefore, summer residents prefer more reliable materials, which can last for several seasons.
It is better to give preference to impregnated fabrics. This material is used to make awnings and tents. When purchasing lumber, keep in mind that you cannot use fresh lining. The reason is that any lumber undergoes shrinkage.
During the drying process, the material loses its shape and previous dimensions. This affects the quality of lumber. Various defects may appear on its surface, reducing its strength. Warping and cracking are the most common defects that have a negative impact on wooden structures. In a structure built from fresh lumber, cracks may appear within a year. Do-it-yourself shower in the country, drawings, dimensions, photos are of interest to many users who want to warn themselves against these shortcomings.
For cladding, you can use the corrugated sheet left over after the construction of the fence.
Polycarbonate - transparent material, which will decorate any shower room. Do not allow any cracks to appear, as dust and moisture will enter them. This is a favorable environment for algae to grow. Gradually, the walls of the polycarbonate will be completely covered with greenish vegetation.
When constructing a shower, it is necessary to provide a ventilation system. Constant moisture can cause wood to rot. Fungus appears on the walls, destroying the structure.
Any container is suitable as a shower tank. It can be a metal or plastic barrel. However, plastic barrels heat water worse. For middle zone this can be critical, since the water requires heating.
Ice water the owner is unlikely to like it country house. Although plastic containers are cheaper than metal ones. But this is the only advantage of such barrels. Best to install metal containers. Not only are they easier to install. The owners will not have to think about how to secure metal barrel. In such a container, the water will heat up much faster. The process of heating water can be accelerated by painting the container black. The disadvantage of this option is the appearance of rust.
People wonder how to make a shower at the dacha with their own hands and how to choose the right water container; when studying photos of the building, you can decide the right choice structure and water tank.
Sometimes a septic tank is installed directly under the shower stall. In this case, the boards are laid with a gap of 3 mm. The water will flow down and fall directly into the drainage hole. In sandy soil, water will not stagnate.
But for clay soil This septic tank option is not suitable. To organize normal drainage, you need to dig a hole in another place. A pallet for building a septic tank can be bought in a store. The finished pallet must be selected based on the size of the future building. It is necessary to install bars around the entire perimeter, otherwise it will dangle.
The foundation can be laid out of bricks. At the bottom of the building you need to lay a layer of gravel 15 centimeters thick. After this, a drain pipe is installed. After the concrete has hardened, you can continue building the shower.
Most summer residents have a desire to take a shower after excavation work. The procedure has a positive effect on human health. Of course, you can buy a shower at finished form. But this will increase construction costs.
It is cheaper to make a shower yourself, without the help of specialists. Water must flow at a certain slope. Don't forget to carry out waterproofing work on your shower. Using a waterproofing film you can prevent the appearance of unpleasant odor. To do this, you need to lay a special mesh. The recommended depth of the drainage pit is 2 m.
To retain heat, it is necessary to install a polycarbonate roof on top of the tank. It will create a greenhouse effect. A mandatory element of the tank is a sensor that informs the user about the water level. If there is no water, they may burn out. Therefore, it is necessary to constantly monitor this parameter. To install a shower floor, you need to install a drain pipe.
What to do if there is no running water in the house? To fill the tank you have to carry water in buckets. This is too time consuming. Before building a shower, think about the water supply. If you have running water, you can fill the tank fairly quickly. Just open the tap and wait until the container is filled to a certain level.
Advanced home owners have come up with a scheme that automates this process. This can be done using a float system. It is necessary to provide for the installation of a system that is designed to drain excess water. According to the laws of physics, the warmest water is at the top. Therefore, water is drawn from above. At the bottom of the tank you can install a hose to drain water into the sewer.
Of course, you can use the energy of the sun. At the same time, you do not have to spend money on electricity. However, this method has significant drawback. It's hard to warm up with the sun a large number of liquids. In addition, this method cannot be implemented in all climatic zones.
In this case, you can use heating using devices that use electricity. Heating elements can heat water to the desired temperature. The person who decides to take a shower sets the temperature regime.
In order for the warmest water to flow into the watering can, you need to attach a piece of foam to the hose. Therefore, water is taken from above. To speed up the heating of water, you can make a coil.
The shower can be built at the farthest end of the site, near the fence. On sandy soil, water will not linger in the sump. Thanks to the rapid absorption of water, rotting can be avoided wooden materials, which are used as cladding materials.
When constructing a shower near a fence, the owner gets an advantage. In this case, it is enough to install 3 pillars. To prevent the pillars from wobbling, it is necessary to dig holes 78 cm deep, fill everything with crushed stone, compact it and fill it with concrete.
After leveling the floor, wood processing begins. You can buy aspen boards and impregnate them with a protective layer. Then the lumber is processed with a grinder.
When installing shelves, consider the weight of the barrel. It must withstand a load of at least 100 kg. The corners will rust during use. To increase service life, the metal frame is painted with a special paint that can be applied directly to rust.
To install polycarbonate, you can use self-tapping screws. Violation of technology can lead to cracking of polycarbonate sheets in sunny weather.
Therefore, people prefer a summer shower equipped with a heating system. To get a convenient and practical design you need great attention devote to the construction site. A draft after a shower can lead to a cold. With the help of heating elements you can heat water to a certain temperature even in cold weather.
- Between the shower design and drain hole there must be a distance of at least 5 meters.
- TO earthworks You can proceed only after calculating the volume of the drainage pit. There is 0.5 cubic meter per person.
- When laying pipes, maintain a slope of 3 to 5 degrees.
The simplest design of a drainage pit is considered to be a cube shape. But this option has a significant drawback. The walls of such a pit lose strength.
It is best to use a cylindrical drain pit. In this case, the load is distributed evenly and the likelihood of destruction is reduced. In order to increase the service life of the shower structure, it is necessary to use biologically based products. Many bacteria are capable of processing waste. Water will be absorbed into the soil faster.
The advantage of a plastic tank is that the water in them does not bloom, the joints do not rust, and the properties of the water do not change.
Electric heaters can be supplied with my own hands. However, it is best to purchase a ready-made tank equipped with a built-in heater. In this case, the system controls all parameters automatically. The installation has a control panel and automatically turns off in case of emergency situations.
In the shower high humidity. Therefore, during construction the following points must be taken into account:
- Instead of an iron pallet, it is advisable to use plastic ladders. They provide good air circulation and prevent water stagnation.
Preparing for summer season is already in full swing. Some use summer cottages for growing crops, others prefer to sow them with lawn grass, plant ornamental plants and just spend time in nature. Be that as it may, on hot summer days you can cool down and take a cool shower everyone wants it. It is not always possible to hire a construction team to build a shower on the site, and such costs will not always be justified. So that you can competently and easily cope with the construction process, in this article we will look at 8 tips for arrangement of a summer shower at the dacha with your own hands.
1. Where to start?
If you have thought about building a summer shower at your dacha, then you already have a rough idea of what it will look like and what you need to purchase. In addition to the design itself, it is very important parameters are:
- Choosing a location;
- Shower size;
- Water tank volume;
- The nature of the construction is temporary or permanent.
Many people try to choose the most secluded corner behind the house or in the shade of trees in order to hide such an intimate structure from prying eyes. This is exactly what is important mistake! By building a shower among the trees, you will be subject to constant attacks from insects that love moisture and coolness, and will deprive yourself of the possibility of natural heating of the water in the tank. That's why place For the future structure, it must be located in an open, well-lit area and in no case be in a hole or in a low area. Even if you plan to use a heated tank, it is more rational to refuse in order to save money on hot days. The building itself should not be located at a short distance from. When taking a shower late in the evening, you need to get home as quickly as possible so as not to get sick.
Concerning size future the buildings and the volume of the water tank. The recommended height of future walls is 200-300 cm. It is necessary to build on the height of the tallest family member, who should not rest his head on the shower head. Width And length shower space is calculated depending on whether the building will have a dry changing room or be limited to only a wet area. The option with a changing room is, of course, more convenient; your clothes will be protected from getting wet, and you will have the opportunity to change clothes comfortably. This way, your shower will consist of two sections separated by a partition. An area of 220x120 cm is quite enough for these two zones, even taking into account the cladding.
Choosing a tank for water, it is necessary to consider the number of people who will use the shower and the intensity of its use. If you come to your dacha only on weekends and use the shower after a hard day at work, then a container that will hold the amount of water at the rate of 40 liters per person is quite sufficient. This will allow each user to continuously pour water for approximately 10 minutes. If many more people take water procedures in a row, you should think about a larger tank. But keep in mind that temporary buildings will not support containers with a volume of more than 200 liters. You can use iron or plastic barrels as the tank itself, or purchase ready-made country models with a built-in watering can. A little advice– if you paint the surface of the tank with black paint, the water in it will heat up much faster due to the ability of black color to attract heat. 
So, let's highlight basic moments:
- Location: in an open, elevated, bright area, at a maximum distance of 2-4 meters from the main building;
- Room size - the height is selected taking into account the height of the tallest family member, the minimum comfortable perimeter is 100x100 cm;
- The size of the water tank capacity is 40 liters for each user, multiplied by the number of people who will consistently take water procedures.
Character future the buildings– temporary or capital, must be selected based on the following parameters:
2. We equip the foundation and ensure the outflow of water
The basis of any structure, of course, is reliable. In the case of a summer shower, the foundation must not only protect the structure from being washed away by groundwater and subsequent subsidence, but also be able to quickly drain used water in large quantities. Building any foundation begins with markings. It is necessary to draw an outline in the selected location. For example, the size of the shower will be 120x120 cm - a person of any size will be comfortable in such a space. You need to drive pegs into the corners of the rectangle, pull the cord around the perimeter and check the dimensions using a tape measure. 
This marking is universal and is performed before the construction of any type of shower. Now let's consider types of foundations for various buildings.
Foundation for a simple temporary shower
For temporary construction, it is enough to remove the top layer of soil 15-20 cm deep within the outlined rectangle and level the area. Now you need to make a pillow that will help drain the water. To do this, prepare a mixture of crushed stone and. You can simply fill the hole halfway with sand and add a layer of crushed stone on top. Small stones will allow soap scum to settle on their surface. Additional filtration a sand layer will avoid rapid mulling. This design can also be placed near the garden without harm to the plants. On top of such a base are usually laid, which serve as the floor in the summer shower. To prevent rapid rotting of wooden materials that will often come into contact with water, it is recommended to place pallets or boards knocked together at a height of 15-20 cm above ground level. For formwork you can use old bricks or . They are laid out around the perimeter of the base, leveled and compacted using a mallet. 
You can use wood to decorate walls or floors only after making it moisture-resistant. The most effective way is impregnation with hot oil and subsequent opening with drying oil or. Arranging such a foundation will allow you to use a summer shower for more than one season.
Foundation for capital construction
If the shower will be used frequently and not by one or two people, you need to think about constructing a permanent building. The most expensive method would be a brick construction. But it is easiest to heat it in the cool season. To do this, it is enough to insulate the walls. The best option there will be a frame building made of metal or wooden beams. Special attention You need to pay attention to laying out a solid foundation. In this case, it is necessary to fill foundation from concrete.
According to the markings, you need to dig a hole about 30-35 cm deep. You need to make mortgages around the perimeter of the rectangle. For these purposes, you can use old iron pipes. The larger their diameter, the stronger the structure will be. In the places where the pipes are located, using a drill, a hole up to 30 cm deep is made, into which pipes or wooden beams are driven. If you use wood, you need to protect its surface by wrapping it in roofing felt or treating it with hot bitumen. After this it is filled in cement-sand mixture. Wooden mortgages can be made not only in the corners, but also along the entire perimeter of the base. To do this, use logs of sufficient width, which can ensure further installation of the floor. The base must be level. This will help prevent water from accumulating in sloped areas. Filling is carried out using arrangement technology. Use special construction beacons and rules. 
Disadvantage the foundation, which is made by pouring, is that you can start arranging the interior space only after it has completely dried. For brick buildings you can use solid cast reinforced concrete slab 170-300 mm thick as a base. This will significantly reduce construction time.
Arrangement of water drainage
Any capital building needs high-quality water drainage.
- Best suited for waste collection septic tank, which must be placed next to the shower stall, but in no case under it. If you decide to save space on your site and still place it under the shower, after a short period of time you will begin to feel a sharp, unpleasant odor inside the building. In addition, there is a risk of soil collapse around the septic tank and, as a result, destruction of the foundation. The recommended distance from the shower stall is 1-2 meters. A drain pipe is removed from the shower tray or a drain ditch is drawn into a septic tank, which must have a sump and a drainage tank. A pit is dug for the receiving chamber. It must be sealed. It could be a tin barrel or. It is recommended to cover the container with a lid to prevent rain or groundwater didn't fill it out. There is a leaky drainage container nearby. It should be installed on a bed of sand and gravel. These two compartments are connected to each other by pipes.
- Another option for collecting waste water is cesspool. To equip it, you need to dig up about 2m3 of earth. This is the optimal volume that will ensure long-term use. A drainage cushion of sand and gravel is made at the bottom of the pit, and the walls must be strengthened and made waterproof. You can cover them with bricks, use ready-made concrete rings, or you can strengthen the hole with old ones. When setting up a drainage hole, do not forget that it needs to be pumped out. In this regard, it must be located in a place where unhindered access for special equipment will be ensured. In addition, the pit must have a distance from the residential building of at least 3-4 meters, as characteristic odors may form.
- For more simple varieties showers that will not be used with great intensity, it is enough to equip drainage well. It will be located directly under the shower stall. A hole is dug, 2 meters deep, a layer of crushed stone is poured at the bottom, and then a plastic pipe with perforation is inserted. Such a well is filled with material that will act as a filter. It can be gravel, crushed stone, old broken bricks, slag. The well is filled to the very top, then covered with a layer and covered with soil. Already installed on top wooden pallet on the formwork, which has slots for water infiltration. This is the most accessible, but no less effective method which will ensure the necessary outflow of water.
The easiest way to ensure water supply is to install a plastic tank or an old one on the shower roof. iron barrel, paint it black to increase the rate of heating of water by the sun's rays, and connect a hose to it, with the help of which water will flow into the tank. A water supply hose is required, especially if the tank volume is 100 liters or more. Disadvantage tanks with natural heating is that in the cool season their use is problematic. Therefore, many people prefer tanks With heated There are three types of such systems:
Installation selected tank can be done in two ways - placing the tank directly on the roof of the cabin or on a special frame. The second case is rational to use if the volume of the tank is impressive, and the building may not support its weight. It is enough to make a frame from old iron pipes over the shower roof or from wooden beams. This method of placement will help to avoid significant heat loss and speed up the heating time of water.
4. The simplest ways to organize a summer shower
It happens that a summer cottage is visited very rarely, and then not for work, but more for relaxation. In this case, the shower can be a simple design that you can even bring with you.
- Portable shower. This design looks like a large heating pad and is made of the same material. After filling the container with water, it twists special nozzle, at the end of which there is . There is a loop at the opposite end, which is convenient for hanging the container on a tree or hook. By placing the container in a well-lit place, the water will heat up very quickly. The volume of such a “shower” is 10-15 liters. This entails restrictions regarding the duration of water procedures and the number of people who can use it. But this is a very convenient and inexpensive option for one person.
- Shower stand– is an iron pipe on legs, which is equipped with a shower head and a hole for connecting a hose. This rack is convenient because it can be placed in any convenient place and, if necessary, brought into the utility room for storage. Disadvantage its lack of a water tank. That is, if there is no warm water on the site and normal pressure in the system, you will have to take a cold shower.
- Usage shower system. The shower column is a metal rod to which the overhead shower and mixer are attached. In order not to bother with arranging a special room for its placement, many attach the shower system directly to the wall of the house or outbuilding. To do this, water is drained from the wall. The wall of the building is protected from moisture. You can veneer it, or with other materials that are available. For convenience, you can separate the space with a curtain, and place a wooden pallet or rubber mat on the floor.
Let us remind you that this is an option for rare use. For the time when you are not at the dacha, the system can be removed and the output can be closed with a special plug.
All of the above types of showers are good because they do not require a foundation or drainage. But also the disadvantage is obvious– the possibility of their use depends entirely on weather conditions.
5. Do-it-yourself summer shower made of wood
To erect a wooden building you you will need:
- Related timber;
- Fastening elements;
- Rubber hose;
- Shower head or shower set;
- Crushed stone.
Construction begins with the construction of a pit for water drainage. It is necessary to remove the top layer of soil 30-40 cm deep and fill it with crushed stone. This way, the soil under the shower stall will quickly absorb water, and the soap residue will remain on the rubble. Now you need to do formwork, to protect the wood from rotting. In the corners of the pit, bricks are laid in a level. The height of the formwork must be at least 15 cm.
Now let's move on to construction frame. You should start from the foundation. It requires boards 15 cm wide and at least 3 cm thick. The size of the base must correspond to the size of the pit. To fasten boards together, it is better to use threaded connections. Over time, the joints will not weaken even under significant weight, unlike conventional ones, which can “slip” out of the mounting hole. 4 beams with a cross section of 7×10 cm are attached to the base.
Frame dressing performed using side and two transverse jumpers, which are inserted into the grooves. The same jumpers will strengthen the frame from above, which will ensure stability after attaching a heavy water tank to the roof. At your discretion, you can add a few more jumpers if you think that the design is unreliable. 
For wall cladding You can use thinner wooden planks, lining, false beams, blockhouse and other timber. The main thing is to leave small gaps between the parts, 3-4 mm thick. This is necessary so that the planks can freely expand when wet, without deforming each other, and also shrink freely after drying. Remember that everything wooden parts that will be exposed to constant exposure to water must be carefully primed and varnished. You can soak them in drying oil or hot oil. Especially important before painting. There is a special antifungal antiseptic impregnation. You can start painting after the primer has completely dried.
When the shower is completely ready, you can hang up the tank. You can just put it on cross beams and secure with straps. If the tank is homemade, do not forget to cut a hole in the bottom for the watering can and a hole for the hose in the top. For convenience, several shelves for shampoos, soaps, etc. can be provided inside the cabin. and a couple of hooks for towels and clothes. Such a shower can be built in a weekend, and if necessary materials already existed on the site, then the costs will be minimal. Life time The design of a wooden shower depends entirely on how well you treated the wood and protected it from moisture before construction. Therefore, this point deserves special attention. 
6. Shower cabin made of polycarbonate
Polycarbonate is usually used to create. Therefore, many people associate this material with the greenhouse effect, and, consequently, with inconvenience. This opinion is wrong. To create showers there is a special opaque type of polycarbonate. The most durable building will be one that is made of metal profiles. Working with them is no more difficult than with wooden beams. Profile pipe with a cross section of 40×20 mm and a wall thickness of 2 mm, suitable for constructing a frame. Also to you required steel corner 50×50 mm. The number of profiles is determined depending on the area of the future shower. The only thing worth considering when cutting is that the racks should be 10-15 cm larger than the expected height of the shower. This is necessary so that you can concrete them and not lose height. Work plan will look like this:
- The frame assembly must be performed on a flat surface. Two side drains and two overlapping crossbars are laid on the ground. their straightness is checked. The parts are connected to each other using welding. The second wall is assembled in the same way.
- After welding, finished structures must be installed vertically at the required distance from each other and connected to each other by two transverse profiles. Maintain a 90 degree angle between the walls. The crossbars only need to be fastened on one side; the door will be welded on the other.
- After the frame is assembled, a hole of the required size is dug. The top layer of soil 10-15 cm deep is removed, leveled and a concrete screed is poured. Once the screed has been poured and leveled, it is necessary to install the assembled frame on top so that the racks, which were initially longer, are immersed in. The level checks the verticality of the installed structure and adjusts it if necessary. If the length of the legs exceeds the height of the concrete screed, it is necessary to drive them into the ground until they are completely immersed.
- To collect water, you can install a special steel pallet or provide drainage ditches during concreting.
- For this design it is better to use plastic tanks for flat water. They are easy to install and, moreover, they eliminate the need for arranging the roof.
- Separately, you need to weld the door frame and weld the hinges to the frame. It is more convenient to immediately sheathe the door separately from the walls.
- When covering the walls, attach the polycarbonate directly to the profiles using self-tapping screws.
The color range of polycarbonate, which is used for lining shower enclosures, is very diverse. Therefore, the design can turn out to be very attractive. Caring for this material is very easy, and in the evening it will protect you from the cool wind. 
7. Country shower made of corrugated sheets
One more good material Corrugated sheeting is used to cover the summer shower. This material has a high strength And durability combined with ease. It is windproof. And when its walls warm up throughout the day, it will be comfortable to shower in. Both wooden beams and metal profiles. Metal is, of course, more durable. Therefore, if you still need to purchase materials, give preference to it.
Making the frame is similar to the examples from points 5 and 6. The only thing difference– more crossbars need to be added. This is necessary to securely fix the sheets and impart rigidity to the structure, since the corrugated sheet itself is considered a soft material. Attach the sheets using . Be sure to use spacers to avoid damaging the sheet. You can cut corrugated sheets with metal scissors or using a grinder and a toothed disc. It is not advisable to use other circles. During cutting, the polymer coating, which protects the coating from corrosion, may burn through. The roof is also covered with corrugated sheeting, and the tank is located under it. The gap between the walls and the tank will provide natural ventilation in the cabin and will prevent the formation of unpleasant odors. An unheated tank can be placed on top of the frame. Then there is no need to build a roof. 
8. Brick shower
This is the most labor-intensive design found on summer cottages with year-round accommodation. Benefits This kind of soul has a lot:
- With the proper approach to the construction process, such a shower will last for many years;
- If you use a heated tank, you can take water procedures at any time of the year. Windproof walls also contribute to this;
- It is very easy to insulate such a building by covering the outside with foam plastic;
- A brick shower can consist of two zones - wet and dry, where it is much more convenient to change clothes;
- A brick shower can be combined with a toilet and use one drainage hole;
- Strong walls and concrete foundation will allow the use of very large water tanks without the risk of structural failure.
Disadvantages include high costs associated with the purchase of materials and the duration of work.
Construction must begin with the arrangement foundation. In the selected area, markings are made and a trench is dug around the perimeter with a depth of 20 cm and a width of 40 cm. Now you need to fill the trench with crushed stone or broken bricks and pour in a liquid concrete solution so that it seeps through the stones. 
After the mortar has dried and settled, about a week later, you can begin laying the first layer of bricks. When making masonry, be sure to control verticality after each new row. Don't forget to leave room for the door. Laying down last layer bricks, make mortgages from thick wooden beams. The tank will be attached to them and the roof will be laid. It is also necessary to strengthen the doorway with a metal corner or the same beam. The roof is covered with corrugated sheeting. It is also necessary to provide a small window that will provide lighting and ventilation.
Now we need to arrange drain It is best to install a drainage well under the shower and lay a drain pipe from it into a sewer pit. Then a large number of people can easily use such a shower. Drainage well covered with earth and filled with concrete, first removed outside a drain pipe. To facilitate drainage, you can fill it with a slight slope towards the middle. In this case, the upper edge of the pipe should be flush with the floor. A wooden pallet with holes is placed on the concrete floor.
Optimal tank size is at least 200 liters. When placing it on the roof, provide a hole for the inlet pipe onto which the shower head will be screwed. It can be either purchased or homemade. When using a heated tank, do not forget about the electrical supply. If you are not strong in this matter, then for your own safety, seek advice or help from specialists. Door leaf
can be made of wood or OSB or chipboard covered with galvanized sheet. Thus, you will provide yourself with comfortable conditions for taking water procedures at any time of the year. 
If it is not possible to carry out hot water V a private house or in country house, then in this case it would be advisable to build a summer shower.
How to build a summer shower with your own hands from wood?
To build wooden shower At the dacha with your own hands, you can follow the following instructions:
First you need to select appropriate place for the construction of a structure. When choosing, you should take into account the fact that such a country shower will be constantly exposed to moisture both inside and outside.
Advice: it is better to build such a structure in a well-ventilated area. This is necessary so that the wood dries faster. Also, do not plant bushes, trees or tall plants, since they retain moisture, do not allow air to circulate, and as a result, interfere with the drying of the wood from which the country shower is made.
Production earthworks. For the shower, we dig a hole measuring 1x1 m, 40 cm deep. At the bottom of the pit we lay a layer of crushed stone, which will help the soapy water to be absorbed into the soil faster. Next, you should place cinder blocks in the corners. They must be set according to level.
Next we proceed to frame manufacturing. To do this, we take boards whose thickness is 30 mm and width - 15 cm. A base measuring 1x1 m will be made from them. 4 beams with a section of 70x100 mm are attached to this base. To bandage the frame, side and two transverse jumpers are used, which are inserted into the grooves. They also serve as reinforcement for the roof, on which a hundred-liter tank will be installed.
Works on frame covering. For these purposes, you can use lining, blockhouse or false beams. The gaps between the grooves should be two to three millimeters. This is necessary so that the timber can expand freely when regularly wet. In our case, a material that imitates logs was used to cover the shower.
do-it-yourself shower for your dacha step-by-step instruction. Photo
Finishing work. Before painting, it is necessary to prime the wood. For these purposes, a bioprotective antifungal impregnation is suitable, after drying the surface is painted with façade acrylic water-borne varnish in at least 3 layers.
The next stage of building a shower in the country is tank installation for water.
construction of a shower in the country. Photo
Tip: for a summer shower, it is advisable to use a tank with a minimum volume of one hundred liters.
You can build such a wooden shower at your dacha with your own hands in one or two days.
building a shower in the country with your own hands. Video
DIY summer shower
For construction it is necessary to prepare the following materials:
- timber;
- fasteners (screws);
- shower kit, which includes a bracket, faucet, curved pipe, adapter and nozzle;
- rubber hose.
How to build a summer shower in your country house with your own hands?
Construction procedure:
Compilation drawings. For such a structure it will be necessary to make a wooden pallet in the shape of a circle from dense wood. We will have cardboard of the required size as a template. First you need to place the cardboard on a flat surface and secure it with tape. Next, using measuring devices, draw a circle with two squares located inside. This template will be used to construct the wooden floor.
DIY summer shower drawings
Construction pallet. Our floor will be three-layer. The procedure for installing the base for the floor is as follows:
Works on pipe installation. Combine all the elements that are in the shower set.
DIY summer shower step by step instructions. Video
DIY summer shower step by step instructions. Video instruction
Summer shower for a summer house made of pipes and polycarbonate
This option attracts with its low cost and resistance of materials to action. sun rays and moisture, as well as ease of processing.
The procedure for constructing the foundation and floor
Before you start building a polycarbonate summer shower, you need to decide on its location. For such a structure, an inconspicuous place with a flat surface, away from wells and wells, is suitable.
Site preparation. To do this, fill it with sand and compact it.
Drill or dig four holes into which the foundation posts will be inserted.
Place a layer at the bottom of the hole crushed stone 10-12 cm thick.
Install pipes made of plastic used for laying sewers. We fill them inside and outside.
DIY summer shower step by step instructions. Photo
In the central part it is necessary to dig drainage hole and fill it with crushed stone.
We also fill the area around the blind area with crushed stone.
We make from timber with a cross section of 100x150 mm base for the structure and attach it to the foundation columns. For these purposes, it is necessary to drill holes in the cement and insert plugs into them.
It is also necessary to screw the jumpers to the frame with self-tapping screws and reinforce the structure with steel corners. We lay between the pipe and the timber waterproofing.
Tip: before installing the jumpers, you need to try on the pallet, since it will subsequently be installed between them. Therefore, if necessary, it will be necessary to adjust the frame to the dimensions of the pallet.
Next, you need to display the height of the floor from the 50x50 timber around the entire perimeter and after that you can start installing flooring . The result should be a base with a built-in tray.
The procedure for constructing walls and roofs
Let's start construction wooden frame soul. At this stage it is necessary to provide a doorway. In our case, the height of the walls will be 2.5 meters.
summer shower made of polycarbonate step by step instructions. Photo
A solid one is attached to the rafters sheathing.
Making a layer waterproofing from roofing felt or bikrost.
From the sides we produce sheathing processed board.
To cover roofs We use soft tiles.
After this we process all wooden frame stain in two layers, and then with varnish in two or three layers. For a structure such as a summer shower made of half-carbonate, you will need about 7.5 liters of stain.
Frame cladding polycarbonate With outside. For these purposes, it is recommended to use a special thermal washer, for which holes must be cut on polycarbonate using a cutter.
Door made in the form of a wooden frame. Its height is two meters. To add rigidity, jumpers and jibs are used. Next, the door frame is painted, hung on hinges and lined with polycarbonate.
After that they hang water heating ba k, faucets, curtains, hooks, rugs and other accessories.
At the bottom of the pan it is necessary to drain the drain into drainage pipe , inserted 20-30 cm into the crushed stone base.
At the final stage we produce improvement of the entrance in the country shower. To do this, we dig a hole, fill the foundation with concrete and lay reinforcement in it. After the concrete gains strength, we lay bricks on it, on which the wood steps will be installed. If desired, you can make decorations. For this you will need cement and stones.
We attach the steps.
Do-it-yourself shower for a summer house
The first thing you need to do before starting construction is to decide on location summer shower. A well-lit, calm, slightly elevated place is suitable for such a structure.
Advice: it is advisable that the shower is not located too close to buildings and is built in the same style as them.
Stages of building a shower in the country
Compilation project. It is planned to build a shower consisting of two small rooms. The minimum size of the bathing compartment should be 100x100 cm, changing rooms - 60x100 cm. In our case optimal size soul - 200x150 cm.
At the selected site mark the rectangle dimensions 140x190 cm. We drive pipes in the corners. The foundation for the shower will be piled from two-meter asbestos-cement pipes, the diameter of which is 90-100 mm. They need to be buried in dug holes to a depth of about 1.5 m. 20-30 cm should remain above the ground surface. After this, a drainage and drainage system is installed.
Summer shower project. Photo
To organize water flow, it is done waterproof layer. It can be made from polyvinyl chloride film or roofing felt, which must be laid on an inclined surface. As an option, you can make a reinforced concrete screed.
The top and bottom are made harness frame.
Installation of plank flooring.
Tip: To ensure water flows out of the shower stall, it is recommended to install floorboards with gaps of 10 mm wide.
The shower room should be separated from the changing room by a high threshold and curtain.
Finishing work. The outside of the country shower is sheathed with clapboard or siding, moisture-resistant plywood, fiberboard, etc. For interior finishing, you should also use materials that are not afraid of moisture.
A water tank must be installed on the roof; the water heater is installed indoors.
Do-it-yourself utility block with shower for your dacha
Construction procedure:
Once a suitable location for constructing a shower has been selected, you can begin excavation work: dig foundation pit, fill it with ASG and lay it out point brick foundation.
Once the foundation is ready, you can begin construction wooden frame designs. For these purposes, timber is used.
For sheathing shower on the sides and back in this project, a 10 mm thick board was used. A window and door opening should be provided at the front.
Device roof frame from wooden beam. In this project, window openings should be provided on the folding roof.
The corners should be lined with boards.
Can be used for roofing bitumen shingles.
The door is made of boards. Door handles and steps can also be cut from wood.
All wooden elements necessary paint paint or varnish.
Arranging benches, installing a shower tray, covering walls with plastic, attaching hooks, etc.
Summer shower projects for the garden
Project No. 1
For a shower, you can also use not only a wooden frame, but also a metal one. This design can be installed directly on the ground. A curtain is used as a door in this project.
Project No. 2
Shower can be made from wavy metal sheet, which can be bent in a semicircle. For this option there is no need to install a water heating tank. It will be enough to connect to the water supply.
Project No. 3
This summer shower made from pipes is lined with white plastic on the outside and brown on the inside. The shower stall can be erected on a paved concrete platform. For this option you will need a water heating tank.
Project No. 4
As a floor in such a shower you can use wood flooring. The inside of the room is lined with blue plastic. Instead of a roof, a wooden lattice is used.
Project No. 5
The base of this shower is made of metal pipes. Brown corrugated sheet was used to cover the walls. The roof is also made of corrugated sheets. Light enters the shower room through openings between the wall and the roof.
Project No. 6
Red polycarbonate was used to make this shower. For this option there is no need to install the tank on the roof. To use such a shower stall, you will need to connect it to the water supply.
Project No. 7
The frame of such a shower is made of metal pipes painted in Blue colour. Plastic was used to cover the walls white. A metal structure was made for the tank.
Example No. 8
Country style shower. The frame is made from dry tree trunks. Branches are used for cladding. Logs are fixed on top of the structure, on which a water tank is installed.
Project No. 9
The frame for such a shower is made of metal elements. The floor and wall cladding are varnished wood. This type of summer shower does not have a door or a water tank.
