How to properly charge a gas lighter with gas. How to refill a lighter with a spray can: tips and useful tricks. Refilling with a gas cylinder

One of the best gifts that can last for many years is traditionally a lighter. The service life of a quality product is almost unlimited, provided it is handled with care. If you have become the happy owner of an expensive product from a reputable manufacturer, we recommend that you inquire about how to refill a lighter with gas.

You will need:

Gas canister;
Lighter;
Clip.

Show others

Preparatory stage

We usually carry this item in our pockets or bags. For this reason, before proceeding with the procedure, you need to clean the valve. Take a sharp object and press down on the center of the part. You can use a paper clip, a nail, a nail file, a knife, etc. You will hear a characteristic puff. The release of air from the wave is sufficient to clear the passage.

Let's get to the point

Refueling with gasoline

The Zippo lighter has now become an iconic accessory. As you know, it runs on gasoline.

In order to pour fuel into it, you will have to pull the housing up and remove the mechanism from the shell.
Then turn the device upside down and peel back the felt pad. You will see a fuel chamber; gasoline should be poured into it. This must be done with extreme caution, making sure that no transfusion occurs.
It is recommended to refill a Zippo lighter exclusively with a specialized product offered by the manufacturer under the Lighter Fluid label.

It is better to refill the lighter with gas in the hallway or on the balcony, especially if there is a small child in the house.
If there is very little gas left in the canister and the pressure is very low, it is recommended to place it in the refrigerator for a few minutes before manipulation.
After you manage to properly refuel the gas lighter, be sure to adjust the combustion level valve, setting it to minimum. If necessary, increase the intensity of the fire.

As you know, gifts given with all your heart last much longer. However, much depends on how carefully the owner treats them. We hope our tips will help extend the life of this stylish and expensive accessory, which is the keeper of pleasant experiences.

How...

How to refill a lighter with gas from a can

Refillable gas lighters are sold empty for safety reasons. The procedures for filling a new product with fuel and a used one differ little from each other. How to refill a lighter with gas from a can if it already weakly supports combustion or does not ignite at all is described below.

Do not attempt to fill the lighter with gas immediately after use. Make sure it is empty and leave it alone for enough time for all the mechanisms to cool down.

Regulator installation

Set the flame height control to minimum. This is usually a brass adjustment screw at the base of the housing with a slot for a screwdriver. Some models come with a key to turn the adjustment knob. Many are equipped with a wheel that does not require special tools to rotate. Do not apply a lot of force when rotating the adjusting devices. If difficulties arise in reducing the height of the fire, then most likely the adjusting screw is in the limit position + or -. Try his move in the other direction.

Release of residual gas

Press the fill valve using one of the appropriate tools:

screwdrivers;

ballpoint pen;

paper clips;

toothpicks;

a suitable adapter included with the cylinder.

Hold it in the open position until a hissing sound is heard. When releasing pressure in the tank, carry out all manipulations away from your face.

Some actions seem so intuitively simple that no one thinks about how to perform them. Start the car, make toast, button your jacket - what could be easier? In fact, these simple things may turn out to be more complicated than at first glance. The short guides below will help you not only on how to properly refill your lighter to extend its life, but also how to do it safely for yourself and others.

Do not refill the lighter in closed, unventilated spaces, inside a car, or in cramped spaces.

Under no circumstances do this near sources of sparks or open flames, or near smokers. The tank and can contain butane under high pressure. It is extremely flammable.

Protect your eyes while refueling and try not to inhale gas vapors.

Use only high quality butane, at least triple purified. The cleaner the fuel, the lower the risk of valve clogging. Poor quality gas can lead to lighter malfunctions during operation and problems during refilling.

The gas cylinder does not need to be cooled. If there is a fuel level control window on the body, you will notice a difference from the procedure for refilling a warm lighter.

Lighters do not like long pauses in operation. Try to use them periodically. This will prolong their life. If long-term storage is necessary, release the gas from the tank. How to do this is described in the corresponding section above.

It is not at all necessary to set a large flame and dip a cigarette into it. The greatest heat is at the very tip of the torch and spreads higher in the invisible zone. This knowledge will help preserve the smoker’s mustache and eyebrows, and proper use of the flame will protect the lighter mechanisms from becoming clogged with ash.

Buy a can of compressed air. This is a necessary tool for caring for your lighter. Blowing out valves and clearing debris from hard-to-reach places will be much easier.

There is another simple way to fill with gas. If repeating the instructions you have read yourself seems difficult, entrust this task to specialists.

This video clearly shows how to refill lighters correctly.

This becomes clear during initial refueling. If you have just joined the ranks of happy owners of Zippo gas lighters, consult with the seller when purchasing fuel for the first time.

The type of intake valve may differ for different models. Manufacturers of gas cartridges can also equip them with different attachments. When purchasing fuel, make sure that the nozzle fits the valve of your model. This simplifies the refueling process, guarantees its quality and safety of the process for you and others. You can look for bottles with universal caps.

Algorithm of actions

How to refill a lighter with a spray can correctly:

Select a nozzle for the can and install it. Make sure it is securely fastened.

Prepare the inlet valve of the lighter - clean it of dust (this can be done with a napkin or a regular cotton swab).

Insert the nozzle of the can into the valve of the product to be refilled.

Press the bottle several times until you hear a hissing sound - this indicates that the reservoir is full.

Important: during the first test drive after refueling, the flames may behave aggressively and unpredictably - do not hold the accessory that has just been filled with fuel near your face. After a couple of seconds, the pressure will normalize and the fire will return to its standard size.

There are two ways to get rid of air that can get into the lighter tank when refilling it:

by bleeding the air using a toothpick (you need to turn the product upside down and press the inlet valve with a toothpick or screwdriver);

Having adjusted the fire level, it must be set to a minimum (the product in this mode may not fire immediately, since instead of gas, air will first come out of it).

A can of gas is enough for about 30 refills (consumption depends on the volume of the lighter tank and the capacity of the fuel bottle itself).

5% Especially for readers of our blog, a 5% discount on the entire range of the store using the promotional code BLOG

Note!

Do not try to refill a lighter from a household gas cylinder, it is life-threatening.

Do not fill the product with fuel in areas with open fire sources (lit cigarettes, cigars, matches and candles are also included), operating electrical appliances or poor ventilation.

Do not attempt to fill the lighter with gas immediately after use. Make sure it is empty and leave it alone for enough time for all the mechanisms to cool down.

Regulator installation

Release of residual gas

Press the fill valve using one of the appropriate tools:

screwdrivers;
ballpoint pen;
paper clips;
toothpicks;
a suitable adapter included with the cylinder.

Hold it in the open position until a hissing sound is heard. When releasing pressure in the tank, carry out all manipulations away from your face.

Refilling the tank

Refueling should only be done upside down. The lighter must be taken in your hand so that it can be easily held, preferably with an emphasis on some hard surface. First, shake the gas canister several times.

Insert the nozzle of a can with a suitable nozzle tightly into the filling valve and press it onto the filling rod. If liquid gas begins to fill the tank, the lighter body will quickly cool. Do not prime for more than five seconds. If this is not enough, repeat the procedure after a while. The release of excess gas will indicate that the tank is completely filled.

Checking the lighter

Do not try to remove the fire immediately after refueling.. Allow the cooled case to warm up to room temperature. This will take a few minutes. Rub your hands to evaporate any remaining gas mixture. Set the flame control to a quarter of the maximum setting and try to light the lighter. Be sure to do this away from your face. Don't be surprised if the fire flares up unexpectedly quickly. If everything works properly, adjust the required torch height.

Do not refill the lighter in closed, unventilated spaces, inside a car, or in cramped spaces.
Under no circumstances do this near sources of sparks or open flames, or near smokers. The tank and can contain butane under high pressure. It is extremely flammable.
Protect your eyes while refueling and try not to inhale gas vapors.
Use only high quality butane, at least triple purified. The cleaner the fuel, the lower the risk of valve clogging. Poor quality gas can lead to lighter malfunctions during operation and problems during refilling.
To quickly fill the reservoir to capacity, try pre-chilling it in the freezer for 5-10 minutes. The gas cylinder does not need to be cooled. If there is a fuel level control window on the body, you will notice a difference from the procedure for refilling a warm lighter.
Lighters do not like long pauses in operation. Try to use them periodically. This will prolong their life. If long-term storage is necessary, release the gas from the tank. How to do this is described in the corresponding section above.
It is not at all necessary to set a large flame and dip a cigarette into it. The greatest heat is at the very tip of the torch and spreads higher in the invisible zone. This knowledge will help preserve the smoker’s mustache and eyebrows, and proper use of the flame will protect the lighter mechanisms from becoming clogged with ash.
Buy a can of compressed air. This is a necessary tool for caring for your lighter. Blowing out valves and clearing debris from hard-to-reach places will be much easier.

There is another simple way to fill with gas. If repeating the instructions you have read yourself seems difficult, entrust this task to specialists.

Video

This video clearly shows how to refill lighters correctly.

Gas lighters are divided into flint and piezo lighters by design.

In flint lighters made of plastic, gas enters when the lever under the wheel is pressed, and in metal lighters, when the lid is opened.

Piezo lighters, in turn, are divided into regular and turbo. In conventional piezo lighters, the fire is ignited using an electrical charge. The difference from ordinary ones is that gas is supplied to them under pressure - and the fire is not extinguished by the wind.

Most often, lighters contain highly purified liquefied butane, a mixture of liquefied butane and propane, which is much cheaper, or isobutane.

Pure propane was only used in older style lighters. It was abandoned because this gas is explosive. The boiling point of propane occurs at -20 degrees Celsius, which can lead to an explosion. The boiling point of butane is +10. Butane lighters can only be used when exposed to direct sunlight.

It should be noted that lighters produced in the CIS are designed for a mixture of propane and butane. They can work even with mixtures of low purity. Imported lighters can only run on butane or triple-purified isobutane. These are mainly expensive and popular models of lighters, which low-quality gas can simply ruin. Some branded lighters only run on liquefied isobutane.

The propane-butane mixture has higher pressure than pure butane and a lower degree of purification. This mixture is not suitable for piezo lighters.

Until recently, lighters were produced in cheap disposable versions. Nowadays these types of lighters are very rare. Reusable lighters of silicon or piezo type are mainly produced.

How to refill a lighter?

Refilling a lighter is only relevant if it is an expensive model. The cost of a gas can is much higher than the cost of a regular refillable lighter.

To use a lighter, you need to purchase a can of liquefied butane or triple-purified isobutane.

How to refill a lighter correctly?

1. Turn the lighter over with the refill valve facing up. For most models it is located at the bottom.

2. Insert the canister stem into the valve, press and hold for 10 seconds. In this case, the can must be positioned with the stem down. When refueling is correct, gas should not escape.

3. After refueling, you must wait a few seconds.

4. To get rid of excess air, you need to set the combustion level valve to minimum. This valve is located next to the refill valve on most lighters. In this case, the lighter may not light up, since the air accumulated in it will first escape.

5. Adjust the combustion level. At this stage, a large flame is possible, which will burn out the accumulated dirt.

A can of gas usually lasts up to 30 refills, but this depends on the volume of the can itself and the size of the lighter.